English - 19 / 36
6-1622396 - rev. 3 - 21/09/2021
1:
ground
2:
+24Vdc TX power supply (test photo)
17:
+24Vdc RX power supply
6:
common
3 – 4 – 5: inputs NC or NO contact from photocells PH1, PH2, PH3
The polarity of the inputs can be selected in the advanced menu, via
PH1
,
PH2
,
PS3
.
ATTENTION!
If not used, the photocell inputs should be disabled by setting in ON position DIP2 for PH1, DIP3 for PH2 and DIP4
for PH3 respectively.
8.1 PHOTOCELL CONNECTIONS
8.2 MAGNETIC LOOP CONNECTIONS
In order to connect a magnetic loop to the control unit, it is necessary to install a loop detector. Please refer to the detector instruction
manual for setting up the loop.
1:
ground
17:
+24Vdc loop detector power supply
10:
common (loop detector output)
7 – 8 – 9: inputs NC or NO contact from loops S1, S2, S3 (loop detector output)
Connect the magnetic loop cables to the terminal block of the loop detector.
The polarity of the inputs can be selected in the advanced menu, via
S1
,
S2
,
PS3
.
ATTENTION!
If S3 is not used, a small bridge must be made between terminal 9 and 10.
8.3 STOP COMMAND INPUT (15 – 11)
Connect the STOP control between terminal 11 and common 15 (NC contact). This input is considered a security; the opening of
the contact immediately stops the automation and remains blocked until the condition is restored.
ATTENTION!
If not used, the STOP input must be disabled by placing DIP1 in ON.
8.4 OPEN COMMAND INPUT (15 – 12)
Connect the wired opening control between terminal 12 and common 15 (contact NO).
8.5 CLOSE COMMAND INPUT (15 – 13)
Connect the wired locking control between terminal 13 and common 15 (contact NO).
8.6 STEP-BY-STEP “SS” COMMAND INPUT (15 – 12)
Connect the wired STEP-BY-STEP command between terminal 14 and common 15 (contact NO).
The method of operation of this command is configurable through the parameter
Sbs
in the base menu.
8.7 FLASHING LIGHT (17 – 16)
Flashing output at 24Vac. Use a flashing light without auto flashing circuit. 24Vac 25W max.
8.8 ANTENNA (21 – 20)
Terminal dedicated to the antenna.
8.9 LED INTERFACE BOARD (J1)
Plug-in LED interface card connector.
8.10 BATTERY CHARGER KIT (J2)
Plug-in connector for board BATTERY CHARGER KIT.
8.11 MOTOR (J4)
Plug-in connector for motor and encoder.
Summary of Contents for 12007336
