background image

4

Patch Release Note

Patch 86251-05 for Software Release 2.5.1

C613-10356-00 REV F

IP routes deleted from the route cache occasionally caused a fatal error. This 
issue has been resolved.

The reconnection to the stream printing TCP port failed after a single 
successful connection was made. This issue has been resolved.

The default for the PROXYARP parameter in the SET IP INTERFACE 
command for a VLAN interface was OFF. The default is now ON.

If a patch was running with a major software release, after a VLAN was 
added at the command line, the VLAN was not shown as UP. This issue has 
been resolved.

FTP data transfers did not succeed for some types of NAT. Also, the 
presence of flow control TCP flags meant that some TCP control packets 
were not recognised. These issues have been resolved.

BGP was updated according to the most recently added route. BGP now 
updates to reflect the best available route, regardless of when it was added.

When using a policy routing rule, the firewall did not translate the source 
IP address of a broadcast packet correctly. This issue has been resolved.

Previously, the ADD SWITCH L3FILTER MATCH command was accepted 
if the TYPE parameter was not specified. This command now requires the 
TYPE parameter, and an error message will be returned if the TYPE 
parameter is not specified.

When static DHCP was set to the first IP address in a range, that range 
would stay in the 

Reclaim

 mode. This issue has been resolved.

If the valid and preferred lifetimes of an IPv6 address for a given interface 
were set to infinity, they were not included in the dynamic configuration. 
This issue has been resolved. 

The SHOW VLAN command was displaying a port that did not exist. This 
issue has been resolved.

PCR: 03402

Module: IPG

                                  Level: 2

PCR: 03405

Module: STREAM

                                  Level: 2

PCR: 03407

Module: IPG

                                  Level: 3

PCR: 03410

Module: VLAN, CORE

                                  Level: 3

PCR: 03412

Module: FIREWALL

                                  Level: 3

PCR: 03413

Module: BGP

                                  Level: 2

PCR: 03415

Module: FIREWALL

                                  Level: 2

PCR: 03416

Module: SWI

                                  Level: 3

PCR: 03424

Module: DHCP

                                  Level: 2

PCR: 03426

Module: IPV6

                                  Level: 3

PCR: 03429

Module: SWI, VLAN

                                  Level: 3

Summary of Contents for 86251-05









































Reviews: