Allied Telesis 86251-05 Release Note Download Page 38

Page: 38 / 40

DELETE PPP

Patch Release Note

Patch 86251-05 for Software Release 2.5.1

C613-10356-00 REV F

DELETE PPP

Syntax

DELETE PPP=

ppp-interface

OVER=

physical-interface

[other parameters]

where:

■

ppp-interface

is the PPP interface number, from 0 to 511.

■

physical-interface

is:

•

SYN

•

DS3

•

ISDN-

callname

•

ACC-

callname

•

MIOX

n-circuitname

•

TDM-

groupname

•

TNL-

callname

•

VLAN

n-servicename

Description

This command deletes the specified lower layer interface from an existing PPP
multilink bundle. The interface may be left with no lower layer interfaces.

The OVER parameter specifies the interface to be deleted.

Examples

To delete the PPoE service “

ANY

” on vlan2 as a physical interface from PPP

interface 1, use the command:

DELETE PPP=1 OVER=vlan2-any

SET PPP

Syntax

SET PPP=

ppp-interface

[OVER=

physical-interface

]

[other parameters]

where:

■

ppp-interface

is the PPP interface number, from 0 to 511.

■

physical-interface

is:

•

SYN

•

DS3

•

ISDN-

callname

•

ACC-

callname

•

MIOX

n-circuitname

•

TDM-

groupname

•

TNL-

callname

•

VLAN

n-servicename

Summary of Contents for 86251-05









































Search results

Summary of Contents for 86251-05

Reviews:

Related manuals for 86251-05

Brands by name

Popular brands

Allied Telesis 86251-05, Release Note

Search results

Summary of Contents for 86251-05

Reviews:

Related manuals for 86251-05

Brands by name

Popular brands