background image

202202

49

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Troubleshooting (Electronic Control)

28. Washer Will Not Spin – Low Speed

Is there voltage 

across "H7-1" on the 

control and terminal 

4 on the motor

?

Is there voltage 

across terminals 3 & 

8 of the motor

?

Is there voltage 

across terminals 3 & 

4 on the motor

?

Is there voltage 

across "H7-6" on the 

control and terminal 

4 on the motor

?

Check lid switch 

for proper 

operation.  Check 

wiring from control 

to lid switch to 

supply.

Replace control.

Correct wiring 

between motor 

and control.

Check operation of 

motor 

thermal protector.  

Replace motor if 

necessary.

Yes

No

Yes

No

Yes

No

Yes

No

Is there voltage 

across "H7-3" on 

control to terminal 8 

of the motor

?

Is there voltage from 

"H7-4" on control to 

terminal 1 of the 

motor

?

Is there voltage from 

"H7-2" on control to 

terminal 6 of the 

motor

?

Is there voltage 

across terminals 6 & 

8 of the motor

?

Replace the 

control.

Correct wiring to 

the motor.

Replace control.

Yes

No

Yes

No

Yes

No

Yes

No

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

Unit should 

operate properly.

TLW397S

Summary of Contents for HWNLE2SP111CW01



























































Reviews: