allen 068360 Safety & Operation Manual Download Page 26 | Manualshive

Page: 26 / 60

background image

Introduction to HDX600

This machine is built with user safety in mind. However, it can present hazards if

improperly operated and serviced. Follow operating instructions carefully.

If you have any questions about operating or servicing this equipment, please

contact your Allen Engineering Dealer or AEC Customer Service at 800-643-0095

or 870-236-7751.

The HDX600 riding trowel is a modern high production machine. Finishing rate will vary depending on the operators skill
and job conditions. This riding trowel has ten finishing blades.

The Super Heavy Duty (SHD) Gearboxes are designed to provide exceptional performance with low maintenance and
trouble free use under some of the worst conditions.

All Allen Engineering HDX600 Riders are equipped with a safety shutdown switch and a low oil warning for added job
safety and engine protection. Operating time between fuel refills is approximately 2-1/2 to 3 hours depending on rotor
speeds.

SECTION 2

OPERATIONS

069970

Page 26

«
...
24
25
26
27
28
...
»

Summary of Contents for 068360





























































Reviews:

No comments

Related manuals for 068360

Brand: Lievers Pages: 50

Brand: Sitepower Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands