allen 068360 Safety & Operation Manual Download Page 14 | Manualshive

Page: 14 / 60

background image

SECTION 1

SAFETY

069970

Page 14

Safety-Alert Signs

This manual contains Safety-Alert Signs, as defined below, which must be followed to reduce the possibility of improper

servi ce damage to the equipment or personal injury. Read and follow all Safety-Alert Signs included in this manual.

NOTE

defines an operating procedure, condition, etc. which is essential to

highlight that contains useful or important information.

EMERGENCY

is used for the identification of safety equipment, first aid, or

emergency egress locations.

NOTICE

used to convey safety information on labels and signs.

CAUTION

is indicative of a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

WARNING

Indicative of a potentially hazardous situations that could result in

death or serious injury

DANGER

indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury

Manual Tag Safety Detail

«
...
12
13
14
15
16
...
»

Summary of Contents for 068360





























































Reviews:

No comments

Related manuals for 068360

Brand: MBW Pages: 47

Brand: Bartell Global Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands