Allen-Bradley 1608S-3V480E User Manual Download Page 23

Rockwell Automation Publication 1608S-UM001C-EN-P - November 2018

23

Chapter

 5

Technical Specifications

Table 8 - Electrical Specifications

Attribute

Value

Nominal Voltage

User-selectable, 100V-480Vrms, 1-Phase or 3-Phase Immune to voltage 
fluctuation up to ±10% of nominal and transient over voltages typically present 
on mains supply (impulse withstand Category II of IEC 60364-4-443)

Frequency 

45…65 Hz, auto-sensing

Measurement inputs

1 to 3 channels, Cat. No.: 1068S-3V480K (3-channel)
Up to 6 channels, Cat. No.: 1068S-6V480K (6-channel)

RMS voltage measurement accuracy 

0.2% typical, ± 2% maximum (of full-scale)
True rms

Sample rate

5760 sample/second

Waveform capture rate

32 samples/cycle

Time Stamp

±0.1 seconds typical accuracy
Real-time clock synchronized to UTC (NIST standard) daily, via 
i-Grid and SNTP protocol

Data Storage

Non-volatile event storage > 300 events
Memory cleared after automatic up load to i-Grid.

Voltage Deviation Event detection trigger.

1/2-cycle rms voltage ≤ 87% or ≥115% of set nominal
Adaptive waveform deviation detection of transient events.

Voltage Deviation Event Storage 

8 cycles waveform data (-1…+3 cycles at event start and -3…+1 cycles at the 
event end) Continuous rms voltage trend, up to 2 minutes

Periodic (PRMS) Data Logging

Minimum, Maximum and Average rms voltage recorded for each 10-minute 
period. Min./Max. are lowest/highest sliding 1/2 -cycle rms period

Power supply and battery backup

Powered from Channel 1 (L1-L2 or L1-N), < 25VA load
9VDC external power supply (not provided - for configuration only)
Rechargeable batteries enable measurement & communication during power 
interruptions for up to 2 minutes

Table 9 - Mechanical and Environmental Specifications

Attribute

Value

Enclosure

NEMA 1 (IP20). Indoor use only.
Only non-conducting pollution (degree II)
Dimensions: 291 x 247 x 75 mm (11.4 x 9.7 x 3.0 in.)

Weight

 8.5 lb (3.6 kg)

Operating Temperature

 0… 40 °C (32…104 °F)

Storage Temperature

 -40…+75 °C (-40…+167 °F)

Relative Humidity

 0…95%, non-condensing

Altitude 2000 m

 6 562 ft at 40 °C (104 °F)

Summary of Contents for 1608S-3V480E



























Reviews: