HYDROGEN GENERATOR
H
2
Page 7
•
This product is designed for household use only. Use in a commercial application will void your valuable warranty.
• NEVER attempt to repair or service your ionpia H
2
yourself. Attempting to do so will void your valuable warranty.
Contact AlkaViva Technical Support to arrange service or repair.
• If your ionpia H
2
becomes submerged in water, unplug the power cord from the wall before removing. Failure to do so
could result in shock!
• Filters should be replaced per manufacturer suggestion at the end of the filter life. It is important that the
replacement filters are installed in the correct position with every filter change.
• The ionpia H
2
must be grounded! In the event of malfunction or breakdown the grounding conductor will prevent risk of
electric shock/spark. The electrical plug must be plugged into an appropriate outlet that is installed and grounded in
compliance with all local codes and ordinances.
• When installing your ionpia H
2
use only manufacturer provided parts and equipment. Using third-party or after-market
parts can void your valuable warranty.
• Always install on a solid and level surface. Do not move your ionpia H
2
while in use.
• DO NOT install or use your ionpia H
2
near open heat sources or open flames such as stoves, ranges, heater vents or
candles.
• The ionpia H
2
can be used on 110v~240v. Always be sure to use the appropriate factory electrical plug. Always make
sure that the plug is firmly inserted into the outlet. Never try to make any modifications to manufacturers original
equipment, and never use a damaged power cord.
• Be sure that the power adapter is placed where it will not come into contact with water.
• Protect your ionpia H
2
from freezing temperatures and direct sunlight.
• Only operate your ionpia H
2
with cold water. Hot water will damage your filters.
• If The ionpia H
2
makes strange or unusual noises or odors, unplug the power cord immediately and contact AlkaViva Technical
Support.
• Unplug The ionpia H
2
if you plan on not using it for an extended period (2 weeks). Store your filters in a plastic bag in
the refrigerator to prevent bacterial growth. In cases of extended periods of non-use (4+ weeks), filter replacements may
be necessary.
• Do not use your ionpia H
2
with well water, water with extreme hardness, high sediment or TDS without first contacting
AlkaViva Technical Support.
• Your ionpia H
2
is not under warranty for any damages caused by hard water or environmental conditions.
• Only clean the exterior with warm water, detergent and a soft rag or paper towel. Do not use chemical or abrasive
cleaners – they can damage the surface. Do not spray or pour water over your ionpia H
2
. Never submerge your
ionpia H
2
.
• Do not close, bend, pinch, press or otherwise obstruct inlet supply lines, or equipment.
Install Method 1: At the sink with a diverter (easiest)
1/4" White Hose to Tap Water Inlet Port
Fig. 1
Tools You May Need:
• Standard pliers or channel locks
• A sharp knife or a good pair of kitchen scissors
https://vimeo.com/147759112
Watch video for diverter installation
1. Start by removing the aerator from your faucet. (It will
unscrew counter clockwise.)
2. Thread your new water supply diverter valve into the
place where you removed the aerator. If it does not fit,
please use the appropriate size adapter from your
installation kit.
3. Unthread the compression nut from the side of the
diverter to expose the tubing connector for the white 1/4”
tubing.
4. Slide the compression nut down the supply tubing about 2 inches. Be sure the threads face
the tubing connector on the diverter - you will screw the nut back onto the diverter.
5. Push the white 1/4” tubing over the tubing connector. Be sure to push it onto the connector
as far as it will go. This may require a firm push. Failure to seat it all the way may cause a leak.
6. Slide the compression nut back over the supply line to the diverter valve and thread into
place. Ensure the nut is screwed firmly in place, but do not overtighten.
Part 1
Part 2
1. Connect the white 1/4” tubing into the Water Source Inlet on the back of
The ionpia H
2
. To do this, simply push the white 1/4” tubing into the fitting as far as it will go,
then give it a slight pull. If it is seated properly into the fitting, it will not leak.
NOTE:
Use of faucet port is NOT recommended as it will NOT produce Hydrogen-rich water,
only filtered water.
2. Connect the power supply and adapter to The ionpia H
2
and to the power outlet.
3. Turn the Flow Control knob clockwise or to the right to start the flow of water.
You are now ready to start drinking great tasting, healthy hydrogen-rich water.
Please note that your diverter style may vary, but the installation is the same. Using a pair of
pliers may help to make the installation easier.
