manualshive.com logo in svg

Alicat Scientific 16 Series, Operating Manual, Page: 35 / 40

Share
Download
Alicat Scientific 16 Series Operating Manual Download Page 35

35

Option: 9 Volt Battery Pack

A Battery Pack that uses a common 9 Volt battery can be mounted to the top of your L Series Flow 

Meter. Power is passed from the battery to the flow meter through the 8 pin Mini-DIN connector. Output 

signals from the flow meter or pressure guage are passed through the male connector on the bottom 

of the battery pack to the female connector on top of the battery pack so the signals can be accessed 

normally. Turn the switch on top of the battery pack off when the meter is not in use. (

Note:

 T

he Battery 

Pack cannot be used with Flow or Pressure Controllers

)

Normal (9V alkaline) battery life is approximately 8 hours (30-40 hours with a 9V-lithium battery), however 

many factors can affect this. Replace the battery as often as required. A common indicator that the battery 

may be approaching the end of its life is a sharp increase in the temperature indicated on the meter. 

This false signal can result when the voltage drops below its normally regulated level. This can affect 

the accuracy of the meter so it is good practice to check that the temperature is approximately correct 

(25°C is about room temperature) or use a fresh battery especially if the measurement is critical.

Replacing the Battery: 

 

 

The battery can be replaced with the battery pack installed on the flow meter.

Remove the four Phillips head screws from the back cover and gently remove it as shown in Figure 

9.

Remove the 9V battery, pulling the top of the battery out first.

Remove the old battery from the harness and replace it with a new battery.

Install  the  new  battery  bottom  end  first  and  replace  the  back  cover  so  that  the  cushioning  pad 

presses directly down on the battery.

Replace the four Phillips head screws.

Battery Pack Back Cover Removal

1.

2.

3.

4.

5.

Summary of Contents for 16 Series









































Reviews:

No comments