manualshive.com logo in svg

Alicat Scientific 16 Series, Operating Manual, Page: 14 / 40

Share
Download
Alicat Scientific 16 Series Operating Manual Download Page 14

14

Line Pressure 

– Pressing the dynamically labeled PSIG button located in the upper left corner of the 

display will move the line gauge pressure to the primary display.

Line Temperature 

– Pressing the dynamically labeled °C button located in the upper middle of the 

display will move the process temperature to the primary display.

Volume 

– The volume flow rate is defaulted on the primary display. Pressing the dynamically labeled 

“Volume” button will move the volume flow rate to the primary display if another parameter is displayed 

there.

Flashing Error Message: 

Our flow meters and controllers display an error message (VOV = volumetric 

overrange, POV = pressure overrange, TOV = temperature overrange) when a measured parameter 

exceeds the range of the sensors in the device. When any item flashes on the display, neither the 

flashing parameter nor the flow measurement is accurate. Reducing the value of the flashing parameter 

to within specified limits will return the unit to normal operation and accuracy.

Figure 8. Proper Set Up for Remote Tare on Meters (Momentarily ground Pin 4 to Tare)

Select Menu Mode

Pushing “Mode” once will bring up the “Select Menu” display. Push the button nearest your selection to 

go to the corresponding screen. Push “Mode” again to return to the Main Mode display. (

Note: 

If your 

meter was ordered with Totalizing Mode option (page 34), pushing the “Mode” button once will bring up 

the “Totalizing Mode” display.  Pushing “Mode” a second time will bring up the “Select Menu” display.)

                     Misc

SELECT

MENU

Comm.      Mfg.

RS-232     Data      Menu

Figure 9. Select Menu Display

Summary of Contents for 16 Series









































Reviews:

No comments