manualshive.com logo in svg

Alicat Scientific 16 Series, Operating Manual, Page: 11 / 40

Share
Download
Alicat Scientific 16 Series Operating Manual Download Page 11

11

Standard Voltage (0-5 Vdc) Output Signal

All L and LC Series flow meters/controllers have a 0-5 Vdc (optional 0-10 Vdc) output signal available on 

Pin 6. This is generally available in addition to other optionally ordered outputs. This voltage is usually 

in the range of 0.010 Vdc for zero flow and 5.0 Vdc for full-scale flow. The output voltage is linear over 

the entire range. Ground for this signal is common on Pin 8.

Optional 0-10 Vdc Output Signal

If your meter/controller was ordered with a 0-10 Vdc output signal, it will be available on Pin 6.  (See the 

Calibration Data Sheet that shipped with your device to determine which output signals were ordered.) 

This voltage is usually in the range of 0.010 Vdc for zero flow and 10.0 Vdc for full-scale flow. The 

output voltage is linear over the entire range. Ground for this signal is common on Pin 8.

Optional Current (4-20 mA) Output Signal

If your meter/controller was ordered with a 4-20 mA current output signal, it will be available on Pin 1. 

(See the Calibration Data Sheet that shipped with your device to determine which output signals were 

ordered.) The current signal is 4 mA at 0 flow and 20 mA at the meter’s full scale flow. The output 

current is linear over the entire range. Ground for this signal is common on Pin 8. (Current output units 

require 15-30Vdc power.)

Note:

 

This is a current sourcing device. Do not attempt to connect it to “loop powered “ systems

.

Optional 2nd Analog Output Signal

You may specify an optional 2nd analog output on Pin 2 at time of order. (See the Calibration Data 

Sheet that shipped with your device to determine which output signals were ordered.) This output may 

be a 0-5 Vdc, 0-10 Vdc, or 4-20 mA analog signal that can represent any measured parameter. 

Note: 

This is a current sourcing device. Do not attempt to connect it to “loop powered “ systems.

7

4

6

2

1

DB-9 Serial Port

5

5----------Ground--------------------------------------Ground----------8

3----------Transmit------------------------------------Receive---------3

2----------Receive-------------------------------------Transmit--------5

8 Pin Mini-DIN Port

8

1

2

3

4

5

6

7

8

9

3

 

4

5

6 7 8

2

Figure 4. Mini-DIN to DB-9 Connection for RS-232 Signals

Summary of Contents for 16 Series









































Reviews:

No comments