manualshive.com logo in svg

Alicat Scientific 16 Series, Operating Manual, Page: 21 / 40

Share
Download
Alicat Scientific 16 Series Operating Manual Download Page 21

21

Communication Select Mode

The Communication Select mode is accessed by pressing the button below “Comm. RS-232” on the 

Select Menu display. Please see page 15 for Communication Select mode instructions.

Manufacturer Data Mode

“Manufacturer  Data”  is  accessed  by  pressing  the  “Mfg.  Data”  button  on  the  Select  Menu  display 

(Figure 9, page 14). The “Mfg 1” display shows the name and telephone number of the manufacturer. 

The“Mfg 2” display shows important information about your flow meter including the model number, 

serial number, and date of manufacture (Figure 11, page 16). 

Miscellaneous Mode

The Miscellaneous mode is accessed by pressing the button above the “Misc” label in the upper right 

hand  corner  of  the  Select  Menu  display. The  screen  will  appear  as  shown  in  Figure  12.  Push  the 

button above “Select” to move the cursor even with the item you wish to adjust. Then use the “UP” and 

“DOWN” buttons to make the adjustment. See pages 16 & 17.

NOTE: All Miscellaneous changes are recorded when you exit the Miscellaneous display.

RS-232 Output and Input

Configuring HyperTerminal®:

Open your HyperTerminal® RS-232 terminal program (installed under the “Accessories” menu on 

all Microsoft® Windows® operating systems).

Select “Properties” from the file menu.

Click on the “Configure” button under the “Connect To” tab. Be sure the program is set for: 19,200 

baud (or matches the baud rate selected in the RS-232 communications menu on the meter) and 

an 8-N-1-None (8 Data Bits, No Parity, 1 Stop Bit, and no Flow Control) protocol.

Under the “Settings” tab, make sure the Terminal Emulation is set to ANSI or Auto Detect.

Click on the “ASCII Setup” button and be sure the “Send Line Ends with Line Feeds” box 

is not 

checked

 and the “Echo Typed Characters Locally” box and the “Append Line Feeds to Incoming 

Lines”  boxes 

are  checked. Those  settings  not  mentioned  here  are  normally  okay  in  the  default 

position.

Save the settings, close HyperTerminal® and reopen it.

In Polling Mode, the screen should be blank except the blinking cursor. In order to get the data streaming 

to the screen, hit the “Enter” key several times to clear any extraneous information. Type “*@=@” 

followed by “Enter” (or using the RS-232 communcation select menu, select @ as identifier and exit the 

screen). If data still does not appear, check all the connections and com port assignments.

Changing From Streaming to Polling Mode: 

When the meter is in the Streaming Mode, the screen is updated approximately 10-60 times per second 

(depending on the amount of data on each line) so that the user sees the data essentially in real time. 

It is sometimes desirable, and necessary when using more than one unit on a single RS-232 line, to be 

able to poll the unit.

In Polling Mode the unit measures the flow normally, but only sends a line of data when it is “polled”. 

Each unit can be given its own unique identifier or address. Unless otherwise specified each unit is 

shipped with a default address of capital A. Other valid addresses are B thru Z.

1.

2.

3.

4.

5.

6.

Summary of Contents for 16 Series









































Reviews:

No comments