manualshive.com logo in svg

Alicat Scientific 16 Series, Operating Manual, Page: 16 / 40

Share
Download
Alicat Scientific 16 Series Operating Manual Download Page 16

16

Manufacturer Data Mode

“Manufacturer Data” is accessed by pressing the “Mfg. Data” button on the Select Menu display (Figure 

7). The “Mfg 1” display shows the name and telephone number of the manufacturer. The“Mfg 2” display 

shows important information about your flow meter including the model number, serial number, and 

date of manufacture. 

Main

Alicat Scientific, Inc.

Ph 520-290-6060

Fax 520-290-0109

Mfg 1

Main

Model L-10LPM-D
Serial No 27117
Date Mfg.11/07/2005
Calibrated By.DL

Software GP07R23 

Mfg 2

Figure 11. Manufacturer Data Displays

Miscellaneous Mode

The Miscellaneous mode is accessed by pressing the button above the “Misc” label in the upper right 

hand  corner  of  the  Select  Menu  display. The  screen  will  appear  as  shown  in  Figure  12.  Push  the 

button above “Select” to move the cursor even with the item you wish to adjust. Then use the “UP” and 

“DOWN” buttons to make the adjustment.

NOTE: All Miscellaneous changes are recorded when you exit the Miscellaneous display.

Summary of Contents for 16 Series









































Reviews:

No comments