ALGE-Timing OPTIc3 Manual Download

Page: 40 / 121

Manual

Photo Finish OPTIc3

- 40-

Confirm the time of day <ENTER> on the PC key-

board or click on

Input the same time of day in the other devices you
want to synchronize.

As soon as you confirm the entered time of day the col-
our changes from red to orange. This means the OP-
TIc3 is now ready to receive the synchronization im-
pulse.

The synchronization impulse can be triggered inter-

nally by clicking on icon

or external with an impulse

on channel C0.

When the synchronization is successful the back-
ground color of the window changes to green. After a
few seconds, it shows the new time of day.

With click on icon

(Take time from PC) the camera takes over the time of day from the

PC.

In the footer of the OPTI3NET software it shows the status of the synchronization:

background yellow: time synchronized automatically from PC system

background red:

time set for external sync impulse

background green:

time is externally synchronized

Summary of Contents for OPTIc3


























































































































Search results

Summary of Contents for OPTIc3

Reviews:

Related manuals for OPTIc3

Brands by name

Popular brands

ALGE-Timing OPTIc3, Manual

Search results

Summary of Contents for OPTIc3

Reviews:

Related manuals for OPTIc3

Brands by name

Popular brands