ALGE-Timing OPTIc3 Manual Download Page 13 | Manualshive

Page: 13 / 121

background image

Manual

Photo Finish OPTIc3

-13-

4

Connection of Camera

Please make sure the following three conditions are fulfilled in order to successfully connect
the camera to a PC:

•

setup of the camera must fit to your network configuration

•

connection by Ethernet or Wi-Fi must work OK

•

power supply of the camera must be OK

4.1

Network connection

The OPTIc3 camera us connected by Ethernet or Wi-Fi to a PC. The camera has a pre-ad-
justed DHCP-network setup. Make sure that the camera setup is suitable to your network
setup; otherwise the camera will not be found and visible in your network. In case you have to
change the network setup of the camera use the separate software “OPTIc3 IP Configurator”
further described below.

4.1.1 OPTIc3 IP Configurator

The pre-adjusted DHCP setup for the network connection can be adapted to your requirements
with separate software called „OPTIc3 IP Configurator“. This software is automatically installed
on your PC with the installation of OPTIc3NET.

«
...
11
12
13
14
15
...
»

Summary of Contents for OPTIc3


























































































































Reviews:

No comments

Related manuals for OPTIc3

Brand: Tamron Pages: 4

Brand: FALEEMI Pages: 14

Brand: Olympus Pages: 43

WDEM-7680LPDN-IO

Brand: Okina Pages: 36

Micro Visioval 294200

Brand: Virax Pages: 36

Brand: Kodak Pages: 89

Brand: XtendLan Pages: 33

Brand: National Geographic Pages: 132

Brand: FujiFilm Pages: 134

Brand: Elvox Pages: 12

Brand: TRASSIR Pages: 2

Brand: GlobalMed Pages: 2

Brand: WITHROBOT Pages: 24

Brand: AgfaPhoto Pages: 16

Brand: Quartet Pages: 29

Brand: Nauticam Pages: 29

Brand: hc-cargo Pages: 52

WEATHERMATIC 35DL

Brand: Minolta Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands