Alfa Network Color Tester, Technical Manual

Page: 42 / 45

Technical Manual
– Color Tester
42
TROUBLE SHOOTING EN
ERROR
CODES
ERROR
DETECTED
ERROR
DESCRIPTION
TROUBLESHOOTING
401-408
B”X”_SUPPLY_CALC_ERROR, where “X” =
1..8
In CONTINUOUS dispensing the
Number of steps of the "X"
BASE to carry out is NOT a
multiple of a whole stroke
Check for consistency errors between the
tables and the circuit installed on the
machine. Verify the proper installation of
the calibration tables in the Machine menu.
409-432
C”X”_SUPPLY_CALC_ERROR, where “X” =
1..24
In CONTINUOUS dispensing the
Number of steps of the "X"
COLORANT to carry out is NOT
a multiple of a whole stroke
Check for consistency errors between the
tables and the circuit installed on the
machine. Verify the proper installation of
the calibration tables in the Machine menu.
451-482
DISABLED_REQUIRED_CIRCUIT_”X”_ERR
OR, where “X” = 0..31
"X" Slave must dispense but is
erroneously Disabled
Load the Slave configurations onto the new
MAB board.
501-508
B”X”_COLOR_HOME_POS_ERROR, where
“X”=1..8
Error in the HOMING procedure
of the "X" BASE
Check the correct operation of the
photocell and the correct movement of the
"X" BASE stepper
509-532
C”X”_COLOR_HOME_POS_ERROR, where
“X”=1..24
Error in the HOMING procedure
of the "X" COLORANT
Check the correct operation of the
photocell and the correct movement of the
"X" COLORANT stepper
551-558
B”X”_COLOR_HOME_BACK_ERROR,
where “X” = 1..8
Loss of steps error in "X" BASE
Dispensing
Decrease the dispensing speed
559-582
C”X”_COLOR_HOME_BACK_ERROR,
where “X” = 1..24
Loss of steps error in "X"
COLORANT Dispensing
Decrease the dispensing speed
601-608
B”X”_COLOR_POS0_READ_LIGHT_ERRO
R, where “X” = 1..8
At the end of the movement from
HOME position to POS0 the
photocell is NOT engaged in the
"X" BASE
Check photocell and stepper operation
609-632
C”X”_COLOR_POS0_READ_LIGHT_ERRO
R, where “X” = 1..24
At the end of the movement from
HOME position to POS0 the
photocell is NOT engaged in the
"X" COLORANT
Check photocell and stepper operation
651-658
B”X”_COLOR_END_STROKE_READ_DAR
K_ERROR, where “X” = 1..8
At the end of the dosing stroke
the photocell is engaged in "X"
BASE
Check photocell and stepper operation
659-682
C”X”_
COLOR_END_STROKE_READ_DARK_ER
ROR, where “X” = 1..24
At the end of the dosing stroke
the photocell is engaged in "X"
COLORANT
Check photocell and stepper operation
701-708
B_”X”_OVERCURRENT_ERROR, where “X”
= 1..8
"X" BASE stepper motor
overcurrent
Check wirings, stepper operation
709-732
C_”X”_OVERCURRENT_ERROR, where “X”
= 1..24
"X" COLORANT stepper motor
overcurrent
Check wirings, stepper operation
751-758
B”X”_SOFTWARE_ERROR, where “X” =
1..8
Logic error in the process
statuses on "X" BASE
Replace electronic board, if the problem
persists request a Firmware update
759-782
C”X”_SOFTWARE_ERROR, where “X” =
1..24
Logic error in the process
statuses on "X" COLORANT
Replace electronic board, if the problem
persists request a Firmware update
783
MOVE_X_AXIS_SOFTWARE_ERROR
Logic error in the process
statuses on X AXIS
Replace electronic board, if the problem
persists request a Firmware update
784
MOVE_Y_AXIS_SOFTWARE_ERROR
Logic error in the process
statuses on Y AXIS
Replace electronic board, if the problem
persists request a Firmware update
785-788
STORAGE_CONTAINER”X”_SOFTWARE_
ERROR where “X” = 1..4
Logic error in the process
statuses on "X" CONTAINER
Replace electronic board, if the problem
persists request a Firmware update
789-790
PLUG_COVER”X”_SOFTWARE_ERROR
where “X” = 1..2
Logic error in the process
statuses on "X" CAPPING
Replace electronic board, if the problem
persists request a Firmware update