background image

Installation Manual 5850-023

TE91K022-EN3

 

BADK 082012 

INITIALLY ISSUED: 3/30/2010 

AUTHORIZATION NUMBER: 1536 

THIS IS TO CERTIFY THAT 

Alfa Laval Inc.

Baldershoj 19, DK 2635 Ishoj, DENMARK  

is hereby authorized to continue to apply the

3-A Symbol to the models of equipment, conforming to 3-A Sanitary Standards for: 

Number: 74-03, Sensors and Sensor Fittings and Connections

set forth below

Conductivity Sensor: TE67K1711111x3 or 4; Level Switch: TE67O0211110x3, 4, 9, 

A, C, D, F, or G; Potentiometric Level Transmitter: TE67H021xxx3x3 or 4; 

Temperature Transmitter: TE67Gx11xxxxx3, 4, 5, or 7.

VALID THROUGH: 

December 31, 2012

Timothy R. Rugh 
Executive Director, 3-A Sanitary Standards, Inc.

The issuance of this authorization for the use of the 3-A Symbol is based upon the voluntary 
certification, by the applicant for it, that the equipment listed above complies fully with the 3-A 
Sanitary Standards designated. Legal responsibility for compliance is solely that of the holder of 
this Certificate of Authorization, and 3-A Sanitary Standards, Inc. does not warrant that the 
holder of an authorization at all times complies with the provisions of the said 3-A Sanitary 
Standards. This in no way affects the responsibility of 3-A Sanitary Standards, Inc. to take 
appropriate action in such cases in which evidence of nonconformance had been established.

NEXT TPV INSPECTION/REPORT DUE: 

March 2015

Summary of Contents for TE67K Series









Reviews: