manualshive.com logo in svg

Alfa Laval OS12, Instruction Manual

Share
Download
Alfa Laval OS12 Instruction Manual Download Page 44

5 Maintenance

Take care not to damage shaft surfaces, in particular where bearings and lipseals will be located
Ensure all fastenings are tightened to the torque settings as shown in Technical Data (See chapter 6 Technical data)

S

Stteepp 44
Lightly lubricate the seal housing profile elastomer (83) and fit onto the seal housing (74).

S

Stteepp 55
Lightly lubricate O-ring (85) and fit onto the seal housing (74).

S

Stteepp 66
Align radial pins in drive ring (75) with the anti-rotation slots in seal housing (74). Fit drive ring (75) into housing (74) making sure
the coil springs holes in the drive ring (75) are facing inwards.

S

Stteepp 77
Lightly lubricate the static face profile elastomer (82) and fit into seal housing (74) groove.

S

Stteepp 88
Align two of the slots in the static face (73) with the axial pins fitted in the drive ring (75), then firmly press the static face
(73) fully home into the seal housing bore (74).

S

Stteepp 99
Gently turn the static unit around, and let it rest on the static face sealing surface (73) on a clean soft lint free tissue.

S

Stteepp 1100
Drop coil springs (87) into coil spring holes in the drive ring (75).

S

Stteepp 1111
Lightly lubricate O-ring (84) and fit onto the static face (76).

S

Stteepp 1122
Align the slots in the static face (76) with the axial pins fitted in the drive ring (75), then firmly press the static face (76) down fully
home into the seal housing bore (74).

S

Stteepp 1133
Spray acetone or similar solvent onto lint free tissue and wipe the sealing surfaces of the rotary face (77) and static face (76) clean.
N

NO

OTTE

E:: Do not spray acetone directly onto the sealing surfaces.

S

Stteepp 1144
Pick seal housing (74) assembly up and whilst holding the assembly compressed, turn it around and slide over shaft sleeve (93)
mating the rotary face (77) and static face (76).

S

Stteepp 1155
Lightly lubricate screw clamping profile elastomer (80) and fit to the rotary holder (94).

S

Stteepp 1166
Place plastic washer (81) in rotary holder (78) aligning the slots in the washer (81) with the pins fitted in the rotary holder bore (94).

S

Stteepp 1177
Lightly lubricate the rotary face profile elastomer (82) and fit to the rotary holder (94) groove.

S

Stteepp 1188
Align the slots in the rotary face (72) with the pins fitted in the rotary holder bore (94), then firmly press the rotary face (72) fully
home into the rotary holder bore (94).

S

Stteepp 1199
Spray acetone or similar solvent onto lint free tissue and wipe the sealing surfaces of the rotary face (72) and static face (73) clean.
N

NO

OTTE

E:: Do not spray acetone directly onto the sealing surfaces.

S

Stteepp 2200
Firmly press rotary holder (94) onto the shaft sleeve (93), mating the rotary face (72) and static face (73).

44

CONTACT CSI FOR MORE INFORMATION  |  CSIDESIGNS.COM  |  [email protected]  |  417.831.1411

Summary of Contents for OS12



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands