Alcorn Mcbride V-Page VP4X User Manual Download Page 24

 

24 

August 31, 2018 

LOCATING A V-PAGE ON A NETWORK 

The V-Page hardware contains 1 physical Ethernet connection but 2 interfaces (V-Page control and Dante audio). 

They are isolated.  This means there are 2 MAC addresses assigned to each “physical” 

V-Page unit hence 2 IPs.  

Furthermore, on any given network there are most likely multiple V-Page units. 

This guide focuses on simplifying locating process of the physical V-Page unit remotely using V-Page station ID, V-
Page MAC/IP (control), Dante MAC/IP (audio) and control <-> audio interface matching in a physical V-Page unit.  
All units must be online (both interfaces) on the same subnet. 

AMI Terminal, one of our free pieces of software available for download on our website, is used to send all the 
commands.  AMI Terminal can broadcast across your subnet by connecting to X.X.X.255, i.e. 192.168.0.255.  AMI 
Terminal cannot connect to a Dante audio interface, but it can match by the Dante information stored in the V-
Page, hence it can be used to match any given Dante interface information to the physical V-Page including physical 
identify by the Dante MAC/IP address. 

Action 

Command 

Response 

Notes 

Pinging all the V-Page Station 

IDs 

“ID” h0D

 

V-Page Station ID from all 

the V-Pages online. 

ID 99 is a default ID if 

Link 

hasn’t been 

performed. 

Pinging all the V-Page IPs

 

“IP” h0D

 

V-Page IP from all the V-
Pages online. 

IP reported is a dynamic 
IP if obtained via DHCP 

or static IP, if one is set. 

Pinging all the V-Page MACs

 

“MC” h0D

 

V-Page MAC from all the V-

Pages online. 

 

Pinging all the Dante MACs 

“UMC” h0D

 

Dante MAC from all the V-
Pages online. 

 

Pinging all the V-Page/Dante 
MAC pairs 

“PMC” h0D

 

V-Page 

MAC, Dante MAC” 

from all the V-Pages online. 

Response contains both 
of the MACs (V-Page and 

Dante) from a single V-
Page unit. 

Physically identifying by V-Page 
Station ID 

“XFN” h0D

 

 

“R” from matched 

V-Page 

and V-Page physically blinking 

for a short period of time. 

X is the station ID 
assigned to the V-Page 

unit. 

Physically identifying by V-Page 

or Dante IP 

“X.X.X.XFN” 

h0D 
 

“R” from matched 

V-Page 

and physically blinking for a 
short period of time. 

X.X.X.X is the V-Page or 

Dante IP address. 

Physically identifying by V-Page 
or Dante MAC 

“X:X:X:X:X:XFN” 

h0D 

 

“R” from matched 

V-Page 

and physically blinking for a 

short period of time. 

X:X:X:X:X:X is the V-
Page or Dante MAC 

address. 

 

Summary of Contents for V-Page VP4X



























Reviews: