Alcatel-Lucent MDR-8000, User Manual, Page: 45 / 130

4-35
Figure 4 - 20 Audio 1 Provisioning (Sheet 1 of 2)
AUDIO 1:
AUDIO 2:
RS-232
MCS
TMN
Channel 3 MCS Transport RF/Rptr PPP Transport RF/Rptr
Channel E-Lead Off -GND
Level M-Lead 0/0 Norm
Address A12A J308/J309 Input Clocks
RSS
J310 Modem J308/J309 Termination RDS/RAS/RCD
Channel 1 Channel 2 Repeater D/1
Channel E-Lead All Call Detect Off -GND DTMF
Level M-Lead 2-Wire Auto Squelch 0/0 Norm 00 Address
Radio Configuration Service Channel WaySide DS1 Facilities DS3 Facilities
Alcatel User Interface – [System, DS3, and DS1 Provisioning -- MDR-8000 DS3]
File View Setup Options
F6
Performance Alarm Status
F4
Analog Monitor Station Alarm
F7
Provisioning
F9
User Control
F8 F5
Prov. Save
F3
Thursday, March 7, 2000 1:27:15 PM USI Version R1.03 Controller Version R1.03 MDR-8000 3-DS3
ELMC Address:
ELMC Description:
J7914
DURANGO
LOCAL DS3 PROVISIONING
Communicating***
Audio provisioning is required only if 4-wire audio equipment (external equipment not part of
the radio) is supplied and the external audio equipment is connected to audio port 1 J316 or
audio port 2 J317 on the radio backplane. These provisionable 4-wire audio functions should
not be confused with the 2-wire audio handset. The handset is fully operational after it is
connected to the TEL jack on the radio controller module, provided the radio is provisioned
Audio 1.
The most common audio provisioning is: 1:, 2:, or 3: AUDIO 1 0/0 Norm.
Note
The 2-wire handset is transported over Audio 1 only.
Note
0/0 – RADIO REQUIRES 0 dBm AUDIO INPUT SIGNAL AT CONNECTOR J316.
THE RECEIVED AUDIO SIGNALS ARE NOT AMPLIFIED. THE RADIO
OUTPUTS 0 dBm ON AUDIO 1 CONNECTOR J316. THIS SELECTION IS
NORMALLY SUFFICIENT IF THE RADIO AND EXTERNAL AUDIO
EQUIPMENT ARE LOCATED IN THE SAME SHELTER, ROOM AND EVEN
BUILDING. LONGER DISTANCES (SUCH AS BETWEEN BUILDINGS) MAY
REQUIRE AMPLIFICATION ON THE OUTPUT SIGNAL. IN THIS CASE,
SELECT
-16/+7 WHERE THE RADIO INPUT REQUIRED IS -16 dBm AND THE
RADIO AMPLIFIES RECEIVED AUDIO SIGNALS TO PROVIDE A +7 dBm
OUTPUT AT AUDIO 1 CONNECTOR J316.
1:, 2: OR 3: – THE 64 kb/s SERVICE CHANNEL TO BE INSERTED INTO RADIO
OVERHEAD IS 1. IF SERVICE CHANNEL 1 IS ALREADY IN USE, SELECT SERVICE
CHANNEL 2 (
2: ) OR SERVICE CHANNEL 3 ( 3: ) FOR THE AUDIO CHANNEL. WHATEVER
IS SELECTED FOR SERVICE CHANNEL 1, 2, OR 3, IT MUST BE THE SAME END-TO-END.
SELECT E-Lead-24Vdc OR E-Lead GND TO
BE APPLIED TO SERVICE CHANNEL E-LEAD.
NORM – MODE OF OPERATION SELECTED IS NORMAL . IN THIS MODE
THE RADIO REQUIRES AN OFF HOOK SIGNAL FROM THE EXTERNAL
AUDIO EQUIPMENT. THIS MEANS THAT THE AUDIO EQUIPMENT USED
TO CONNECT TO THE RADIO MUST HAVE E AND M-LEAD SIGNALING
CAPABILITY (MOST AUDIO EQUIPMENT DOES HAVE THIS CAPABILITY).
IF THE EXTERNAL AUDIO EQUIPMENT DOES NOT HAVE E AND
M-LEAD SIGNALING CAPABILITY, SELECT
O/H AND A CONSTANT
OFF-HOOK SIGNAL WILL BE PROVIDED AUTOMATICALLY BY THE
RADIO CONTROLLER SOFTWARE.
MDR-1035A
09/06/04