manualshive.com logo in svg

Alcatel-Lucent 9927, Manuallines, Page: 216 / 247

Share
Download
Alcatel-Lucent 9927 Manuallines Download Page 216

Control the cabinet while it is being lifted

NOTICE

When Moving Cabinet

When moving a cabinet, do not tilt the cabinet beyond 30 degrees from vertical. Do not
stand under the cabinet.

A rope tied to the pallet attached to the cabinet should be used to guide the cabinet while
it is being lifted. The rope must be sufficiently long. As the cabinet is being lifted and
transported, use the rope to guide the cabinet and prevent the cabinet from tilting or
swinging.

Always lift cabinets carefully. Also, keep the boom line tight to prevent the cabinet from
tipping while the cabinet is being moved. At the end of the lift, slowly place the cabinet
on the ground.

Unsafe if lifting sling angle is
less than 45 degrees
to the top of the cabinet.

Lifting sling

angle

Boom line

B connecting link or clevis

Slings

Lifting
Eyebolt

Slings

Unsafe if lifting sling angle is
Less than 45 degrees
To the top of the cabinet.

Lifting sling

angle

Boom line

B connecting link or clevis

Slings

Lifting
Eyebolt

Modular Cell cabinet

60ECv2 battery cabinet

Guidelines for lifting and moving cabinets

Lifting and moving cabinets

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

D-6

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

9927 Dist BTS Outdoor

401-703-516

Issue 1

March 2012

Summary of Contents for 9927
























































































































































































































































Reviews:

No comments