Home
/
Alcatel-Lucent
/
9927
/
Manuallines

Alcatel-Lucent 9927, Manuallines, Page: 114 / 247

Share

Page: 114 / 247

Alcatel-Lucent 9927 Manuallines Download Page 114

...................................................................................................................................................................................................

2

Place the top strut on the wall and make sure that the strut is level. Use the holes at the
ends of the strut as a template to mark the positions of the holes to be drilled in the wall.

...................................................................................................................................................................................................

3

Place the bottom strut against the wall below the top strut according to the figure below.
Use the holes in the strut as a template to mark the positions of the holes to be drilled in
the wall.

...................................................................................................................................................................................................

4

Drill holes in the wall at the marked positions using an appropriate concrete drill bit for
selected anchor.

...................................................................................................................................................................................................

5

To install the top strut, place the top strut against the wall. Drive the anchor bolts into the
holes of the strut until nut and washer are flush with the strut.

...................................................................................................................................................................................................

6

Tighten the nut to proper torque requirement.

Basic site preparation requirements and footprints for DC
Distribution/Fiber Management Box

Site requirements for wall mount installation of DC

Distribution/Fiber Management Box

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

7-6

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

9927 Dist BTS Outdoor

401-703-516

Issue 1

March 2012

«
...
112
113
114
115
116
...
»

Summary of Contents for 9927
























































































































































































































































Reviews:

No comments