manualshive.com logo in svg

Alcatel-Lucent 9927, Manuallines, Page: 145 / 247

Share
Download
Alcatel-Lucent 9927 Manuallines Download Page 145

The following figure shows a typical method for connecting an antenna cable.

RF antenna connections

The RRH accepts two RF antenna cables on top of the unit.

The connectors are 7/16 DIN. One 7/16 DIN connector is for Tx/Rx, the other is Rx-only.

An external RF surge protector is not required.

RF antenna cable requirements

The RRH can support up to two RF antennas per one-sector configuration with
transmit/receive diversity. The RF antenna cable must satisfy the following requirements:

•

Impedance: 50 ohms

•

Attenuation: < 3 dB

•

Antenna jumper cable at the baseband cabinet end must be equipped with a 7-16 DIN
center pin straight male connector.

•

Surge protection (not required for outdoor)

•

properly grounded.

DOUBLE HOLE LUG
TO BUS BAR

#6 AWG STRANDED INSULATED

COPPER GROUND WIRE

ANTENNA CABLE

CABLE GROUND KIT

RF antenna cable requirements for RRHs

General antenna cable requirements

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

9927 Dist BTS Outdoor
401-703-516
Issue 1

March 2012

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

11-5

Summary of Contents for 9927
























































































































































































































































Reviews:

No comments