Home
/
Alcatel-Lucent
/
7750 SR OS
/
Interface Configuration Manual

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 170 / 444

Share

Page: 170 / 444

Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 170

Card, MDA, and Port Command Reference

Page 170

7750 SR OS Interface Configuration Guide

TDM commands

config

—

[

no

]

port

{

port-id

}

—

—

{

long

|

short

}

—

[

0dB

|

-7.5dB

|

-15.0dB

| -

22.5dB

]

—

133

|

266

|

399

|

533

|

655

}

—DS1 Commands

—

[

no

]

ds1-id

—

{

2e3

|

2e9

|

2e11 | 2e15

|

2e20

|

2e20q

|

2e23

|

ones

|

zeros

|

alter-

nating

}

duration

duration

— no

—

bit-error-insertion

rate

— no

bit-error-insertion

—

[

no

channel-group

channel-group

—

—

cell-format

cell-format

—

value

—

—

down-count

— no

—

time-interval

— no

—

up-count

— no

—

{

16

|

32

}

—

description

description-string

— no

description

—

[

no

egress-scheduler-override

—

priority-level

rate

pir-rate

[

cir

cir-rate

]

— no

priority-level

—

rate

— no

—

egress-scheduler-policy

port-scheduler-policy-name

—

{

atm

|

bcp-null

|

bcp-dot1q

|

ipcp

|

ppp-auto

|

frame-relay

|

wan-mirror

|

cisco-hdlc

|

cem

}

—

frame-relay

—

{

ansi

|

itu

|

none

|

rev1

}

—

{

dce

|

dte | bidir

}

—

intervals

— no

—

threshold

— no

—

threshold

— no

—

count

— no

—

count

— no

—

keepalive

— no

—

keepalive

— no

—

idle-cycle-flag

{

flags

|

ones

}

— no

idle-cycle-flag

«
...
168
169
170
171
172
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments