manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 271 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 271

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 271

n392dce

Syntax

n392dce 

threshold

no n392dce

Context

config>port>sonet-sdh>path>frame-relay
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay

Description

This command sets the DCE error threshold for the Frame Relay Local Management Interface (LMI).

The threshold specifies the number of errors needed to bring down a link.

The 

no

 form of this command returns the 

n392dce

 counter to the default value.

Default

3

Parameters

threshold  — 

Specify the number of errors that will place the channel in an operationally down state.

Values

1 — 10

n392dte

Syntax

n392dte 

count

no n392dte

Context

config>port>sonet-sdh>path>frame-relay
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay

Description

This command sets the DTE error threshold for the Frame Relay Local Management Interface (LMI).

The count specifies the number of errors needed to bring down a link.

The 

no

 form of this command returns the 

n392dte

 counter to the default value.

Default

3

Parameters

count  — 

Specify the number of errors that will place the path or channel in an operationally down 

state.

Values

1 — 10

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments