Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 185

Page: 185 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 185

Configuration Commands

•

Generic Commands on page 185

•

Card Commands on page 187

•

MDA Commands on page 190

•

Interface QoS Commands on page 199

•

General Port Commands on page 203

•

APS Commands on page 216

•

802.1x Port Commands on page 235

•

Network Port Commands on page 240

•

Multilink-Bundle Port Commands on page 242

•

SONET/SDH Port Commands on page 252

•

Frame Relay Commands on page 269

•

TDM Commands on page 274

•

LAG Commands on page 292

•

Multi-Chassis Redundancy Commands on page 299

Generic Commands

description

Syntax

description

description-string

no description

Context

config>port
config>port>sonet-sdh>path
config>port

tdm>ds1>channel-group

config>port

tdm>ds3

config>port

tdm>e1>channel-group

config>port

tdm>e3

config>lag

Description

This command creates a text description for a configuration context to help identify the content in the
configuration file.

The

form of this command removes any description string from the context.

Default

No description is associated with the configuration context.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands