manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 240 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 240

Configuration Commands

Page 240

7750 SR OS Interface Configuration Guide

Network Port Commands

network

Syntax

network

Context

config>port>ethernet
config>port>sonet-sdh>path
config>port>tdm>ds1

config>port>tdm>ds3
config>port>tdm>e1
config>port>tdm>e3

Description

This command enables access to the context to configure network port parameters.

accounting-policy

Syntax

accounting-policy 

policy-id

no accounting-policy

Context

config>port>ethernet>network
config>port>sonet-sdh>path>network
config>port>tdm>ds1>network
config>port>tdm>ds3>network
config>port>tdm>e1>network
config>port>tdm>e3>network

Description

This command configures an accounting policy that can apply to an interface.

An accounting policy must be configured before it can be associated to an interface. If the accounting 

policy-id

 does not exist, an error is returned. 

Accounting policies associated with service billing can only be applied to SAPs. Accounting policies 
associated with network ports can only be associated with interfaces.

Only one accounting policy can be associated with an interface at a time. 

By default, no specific accounting policy is associated with the interface. If configured, the 
accounting policy configured as the default is used. 

The 

no

 form of this command removes the accounting policy association from the network interface, 

and the acccounting policy reverts to the default.

policy-id — 

The accounting 

policy-id

 of an existing policy. Accounting policies record either service 

(access) or network information. A network accounting policy can only be associated with the 
network port configurations. Accounting policies are configured in the config>log>accounting-
policy context.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments