manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 199 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 199

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 199

Interface QoS Commands

access

Syntax

access

Context

config>card>mda
config>port

Description

This command enables the access context to configure egress and ingress pool policy parameters.

On the MDA level, access egress and ingress pools are only allocated on channelized MDAs. 

network

Syntax

network

Context

config>card>mda 
config>port

Description

This command enables the network context to configure egress and ingress pool policy parameters.

On the MDA level, network egress pools are only allocated on channelized MDAs. 

egress

Syntax

egress

Context

config>card>mda>access
config>card>mda>network
config>port>access
config>port>network

Description

This command enables the context to configure egress buffer pool parameters which define the 
percentage of the pool buffers that are used for CBS calculations and specify the slope policy that is 
configured in the 

config>qos>slope-policy

 context.

On the MDA level, network and access egress pools are only allocated on channelized MDAs. 

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments