manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 187 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 187

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 187

Card Commands

card

Syntax

card 

slot-number

 

no card 

slot-number

 

Context

config

Description

This mandatory command enables access to the chassis card Input/Output Module (IOM), slot, and 
MDA CLI context.

The 

no

 form of this command removes the card from the configuration. All associated ports, services, 

and MDAs must be shutdown.

Default

No cards are configured.

Parameters

slot-number — 

The slot number of the card in the chassis. 

Values

1 — 10 depending on chassis model.

SR-1: 

slot-number 

= 1

SR-7: 

slot-number 

= 1 — 5

SR-12: 

slot-number 

= 1 — 10

card-type

Syntax

card-type 

card-type

no card-type 

Context

config>card

Description

This mandatory command adds an IOM to the device configuration for the slot. The card type can be 
preprovisioned, meaning that the card does not need to be installed in the chassis. 

A card must be provisioned before an MDA, or port can be configured. 

A card can only be provisioned in a slot that is vacant, meaning no other card can be provisioned 
(configured) for that particular slot. To reconfigure a slot position, use the no form of this command 
to remove the current information. 

A card can only be provisioned in a slot if the card type is allowed in the slot. An error message is 
generated if an attempt is made to provision a card type that is not allowed.

If a card is inserted that does not match the configured card type for the slot, then a medium severity 
alarm is raised.  The alarm is cleared when the correct card type is installed or the configuration is 
modified.

A high severity alarm is raised if an administratively enabled card is removed from the chassis. The 
alarm is cleared when the correct card type is installed or the configuration is modified. A low 
severity trap is issued when a card is removed that is administratively disabled.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments