Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 242 | Manualshive

Page: 242 / 444

background image

Configuration Commands

Page 242

7750 SR OS Interface Configuration Guide

Multilink-Bundle Port Commands

multilink-bundle

Syntax

[

no

]

multilink-bundle

Context

config>port

Description

This command creates the context to configure bundle properties for this bundle port.

Default

None

fragment-threshold

Syntax

fragment-threshold

fragment-threshold

fragment-threshold unlimited
no fragment-threshold

Context

config>port>multilink-bundle

Description

This command sets the maximum length in bytes of a fragment transmitted across a multilink bundle.

The

no

form of this command resets the fragment threshold back to the default value.

Default

128

Parameters

fragment-threshold —

Specify the maximum fragment length, in bytes, to be transmitted across a

multilink bundle. Note that the value range is dependent on the MDA type. For example:
channelized MDAs, such as the m1-choc12-sfp, m4-choc3-sfp, m12-chds3, and m4-chds3,
support values of 128, 256, 512; ASAP channelized MDAs support any value in the valid range.

Values

128 — 512 bytes inclusive for MLPPP bundles
128 bytes for IMA bundles

unlimited —

This keyword disables fragmentation.

interleave-fragments

Syntax

[

no

]

interleave-fragments

Context

config>port>multilink-bundle

Description

This command enables Link Fragmentation and Interleaving on the multilink bundle.

The

no

form of this command disables Link Fragmentation and Interleaving on the multilink bundle.

«
...
240
241
242
243
244
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Brand: 4IPNET Pages: 97

Elinx EIRP305-T

Brand: B&B Electronics Pages: 19

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

totalstorage 200

Brand: IBM Pages: 180

EdgeLens INT10G8LR56

Brand: Garland Pages: 30

Brand: Lanner Pages: 59

Brand: Paradyne Pages: 6

IPS Pro-Module-24C-GE-BP-TM

Brand: Trend Micro Pages: 3

Brand: Waver Pages: 36

Ether-GSH24T v3

Brand: AirLive Pages: 2

Brand: Goobay Pages: 20

Brand: Net Optics Pages: 2

ExtremeCloud Appliance E1120

Brand: Extreme Networks Pages: 219

Brand: N-Tron Pages: 2

Brand: Billion Pages: 2

Brand: Cavalry Pages: 16

Brand: MikroTik Pages: 9

Brand: Zte Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands