manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 281 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 281

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 281

32  — 

Use 32 bit checksum for the associated port/channel.

down-count

Syntax

down-count 

down-coun

t

no down-count

Context

config>port>sonet-sdh>path>cisco-hdlc
config>port>tdm>ds1>channel-group>cisco-hdlc
config>port>tdm>ds3>cisco-hdlc
config>port>tdm>e1>channel-group>cisco-hdlc
config>port>tdm>e3>cisco-hdlc

Description

This command configures the number of keepalive intervals that must pass without receiving a 
keepalive packet before the link is declared down. It is expected that the nodes at the two endpoints of 
the cHDLC link are provisioned with the same values.

Default

3

down-count — 

Specifies the number of keep alive intervals that must pass without receiving a keep 

alive packet before the link is declared down.

Values

3 — 16

encap-type

Syntax

encap-type

 {

atm

 | 

bcp-null

 | 

bcp-dot1q

 | 

ipcp

 | 

ppp-auto

 | 

frame-relay 

| 

wan-mirror 

|cisco-hdlc| cem

}

Context

config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1>channel-group
config>port>tdm>e3

Description

This command configures the encapsulation method used to on the specified port, path, or channel. 
This parameter can be set on both access and network ports. 

When the 

encap-type 

is set to ATM the CRC, timeslots, scrambling (if applicable), and idle-cycle-

flags are set to ATM defaults respectively. When the encap-type is changed from ATM, those 
parameters are set to their non-ATM defaults.

When the 

encap-type 

is ATM, ATM sub-layer verification (GR-1248-CORE, 

Generic Requirements 

for Operations of ATM Network Elements (NEs)

) is automatically enabled. When ATM PLCP cell 

mapping is used, the results of this verification include:

• PLCP Severely Errored Framing Seconds

• PLCP Alarm State

• PLCP Unavailable Seconds Counter

When ATM direct cell mapping is used, the result of the verification includes:

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments