manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 272 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 272

Configuration Commands

Page 272

7750 SR OS Interface Configuration Guide

n393dce

Syntax

n393dce 

count

no n393dce

Context

config>port>sonet-sdh>path>frame-relay
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay

Description

This command sets the DCE monitored event count for the Frame Relay Local Management 
Interface (LMI).

The 

no

 form of this command returns the 

n393dce

 counter to the default value.

Default

4

Parameters

count  — 

Specify the diagnostic window used to verify link integrity on the DCE interface.

Values

1 — 10

n393dte

Syntax

n393dte 

number

no n393dte

Context

config>port>sonet-sdh>path>frame-relay
config>port>tdm>ds1>channel-group>frame-relay
config>port>tdm>ds3>frame-relay
config>port>tdm>e1>channel-group>frame-relay
config>port>tdm>e3>frame-relay

Description

This command sets the DTE monitored event count for the Frame Relay Local Management Interface 
(LMI).

The 

no

 form of this command returns the 

n393dte

 counter to the default value.

Default

4

Parameters

number  — 

Specify the diagnostic window used to verify link integrity on the DTE interface.

Values

1 — 10

t391dte

Syntax

t391dte 

seconds

no t391dte

Context

config>port>sonet-sdh>path>frame-relay
config>port>tdm>ds1>channel-group>frame-relay

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments