manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 266 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 266

Configuration Commands

Page 266

7750 SR OS Interface Configuration Guide

min-vp-vpi

Syntax

min-vp-vpi 

value

Context

config>port>sonet-sdh>path>atm
config>port>multilink-bundle>ima>atm
config>port>tdm>ds1>channel-group>atm
config>port>tdm>ds3>atm
config>port>tdm>e1>channel-group>atm
config>port>tdm>e3>atm

Description

This command sets the minimum allowable virtual path identifier (VPI) value that can be used on the 
ATM interface for a VPC.

Parameters

value — 

Specify the minimum allowable VPI value that can be used on the ATM interface for a VPC.

Values

0 — 4095 (NNI)
0 — 255 (UNI)

Default

0

ilmi

Syntax

ilmi

 [

vpi/vci

]

no ilmi

Context

config>port>sonet-sdh>path>atm

Description

This command creates an ILMI link PVCC by default on VPI/VCI 0/16. Deleting an ILMI link 
deletes the PVCC. ILMI is supported only on ATM interfaces on SONET/SDH paths.

Parameters

vpi/vci — 

Specifies the PVC identifier (vpi/vci).

Values

vpi 

0 — 4095 (NNI)
0 — 255  (UNI)

vci 

1, 2, 5 — 65535

egress

Syntax

egress

Context

config>port>sonet-sdh>path>atm>ilmi

Description

This command enables the context to configure egress traffic attributes for the ILMI link.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments