background image

Instructions for installation and operation  -  English 

 

Installation & Use Pares - Marami - Code 10013216 - Edition 2 - 10/2011 – Page 6 

PRE-WIRING OF ELECTRICAL CONNECTIONS 
 
The  electrical  installation  for  the  spa  is  the  customer’s  responsibility.  Under  no  circumstances  are  our  teams 
authorised to carry out work on the customer’s electrical installation. We recommend you call upon the services of a 
certified electrician to ensure compliance of your installation.

 

The installer should refer to standards.

 

 
See also the following documents: 

-

Product technical sheet 

-

Electrical system, safety distances and danger zones for SPA pools with hydromassage 

 

It is the installer’s responsibility to choose the materials according to the planned use, to make sure the works are carried 
out properly, to check the state of the installation to which the appliance is connected, and also to ensure its compliance 
with  the  safety  standards  to  be  applied  during  its  use  and  during  the  maintenance  operations,  making  sure  that  the 
installation can be checked easily. 
 
The  power  supply  installation  must  comply  with  the  provisions  of  the  national  legislation.  The  spa  must  be  permanently 
connected,  without  any  intermediate  connections,  to  the  electric  power  supply  network  and  to  the  protection  circuit 
(grounding). 
 
The spa must be fed without fail through a differential circuit-breaker with a release threshold of 30mA. For the grounding 
connection  provided  for  by  the  directives  in  force,  the  installer  must  use  the  terminal  provided  for  this  purpose  on  the 
electrical box. More specifically, it is necessary to guarantee the equipotentiality of all the metal masses located close to the 
spa. 
 
The connection to the mains must include the grounding connection and be: 

-

of the fixed type 

-

sized for maximum consumption (as shown on the table of the electrical characteristics).  

-

with a level of resistance to liquid penetration (IPX5) in accordance with standards. 

 
 

This  appliance  is  intended  for  home  use.  In  the  event  of  public  use,  guarantee,  in  addition  to  the  technical  and 
safety provisions stipulated by our factory, total compliance with the standards of specific laws for the circuit, safety 
and treatment of the water in force in the country where the spa is to be installed. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Marami
































Reviews: