background image

Instructions for installation and operation  -  English 

 

Installation & Use Pares - Marami - Code 10013216 - Edition 2 - 10/2011 – Page 26 

Stand-By Function 
 

This function enables you to do maintenance work on the spa by changing  the filtration cartridges while blocking all the 
functions for a period of 60 min. without having to disconnect the spa. 
The Stand-By function is activated by pressing the 

Filtr.

 key for 5 sec. (once the function has started you have to wait 30 sec 

for  everything  to  come  to  a  stop).  When  the  function  is  activated,  you  will  see  displayed  alternately  on  the  screen  the 
message 

Sby 

and the time remaining in minutes. 

 

 

 

Programming of the clock 
 

-

Press on the « Clock » key for 5 seconds until the time displayed starts flashing. 

-

Use the keys + and – to set the value of the hour, then press again on« Clock » to change the minutes. Likewise use the 
keys + and – to set the minutes. 

-

Lastly validate the programming by pressing the « Clock » key. 

 
Locking of keyboard 
 

This function enables you to lock your keyboard in 2 different ways, either completely or partially. 
Partial locking enables you to block all the « programming » part, i.e. all the keys at the bottom (Clock, Eco, Filtr., +, -) 
As for total locking it blocks the entire keyboard. 
 

Partial locking:

  

 
 
 

 

 

Total locking: 
 
 
 

 

 

Unlocking of the keyboard: 
 

 

 

Press on the Eco key 
for 3 seconds 

 

LocP is displayed together 
with a key symbol 

 

LocF is displayed 
together with a 
key symbol 

 

Press on the Eco key for 5 seconds. 
You will see LocP appear then by 
keeping it pressed LocF will be 
displayed 

 

ULoc is 
displayed  

 

Press on the Eco 
key for at least 
5 seconds.  

Summary of Contents for Marami
































Reviews: