Albatron KX400+ Pro User Manual Download Page 45

Page: 45 / 71

KX400+ series mainboard

Advanced BIOS Features

Virus Warning

This option allows you to choose the VIRUS warning feature for IDE Hard Disk boot

sector protection. If this function is enabled and someone attempt to write data into
this area, BIOS will show a warning message on the screen and alarm beep.

Options:
Disabled (default)

Virus protection is disabled.

Enabled

Virus protection is activated.

CPU Internal Cache

Make CPU internal cache active or inactive. And system will slow down if disable

this item. Options: Enabled (default)

、

Disable.

External Cache

This option allows you to enable or disable “Level 2” secondary cache on the CPU to

enhance performance.

Options:
Enabled (default)

Enable cache.

Disabled

Disable

cache.

CPU L2 Cache ECC Checking

Make CPU L2 cache ECC function active or inactive. Options: Disabled

、

Enabled

(default).

Quick Power On Self Test

Allow the system to skip certain tests while booting. This will decrease the time

needed to boot the system.

Options:
Enabled (default)

Enable quick POST.

Disabled

Normal

POST.

Swap Floppy Drive

If the system has two floppy drives, choose enable to assign physical drive B to

logical drive A and vice-versa. Options: Disabled (default)

、

Enabled.

Boot Up NumLock Status

Selects power on state for NumLock.
Options:
On (default)

Numpad keys are number keys.

Off

Numpad

keys

are

arrow

keys.

Summary of Contents for KX400+ Pro








































































Search results

Summary of Contents for KX400+ Pro

Reviews:

Related manuals for KX400+ Pro

Brands by name

Popular brands

Albatron KX400+ Pro, User Manual

Search results

Summary of Contents for KX400+ Pro

Reviews:

Related manuals for KX400+ Pro

Brands by name

Popular brands