Albatron KX400+ Pro User Manual Download Page 3

Page: 3 / 71

KX400+ series mainboard

Chapter 1. Getting Started

Introduction

Congratulations on choosing the KX400+ Series mainboard! This series includes

the KX400+

、

KX400+ PRO

、

KX400+ PRO-C, and is based on VIA

VT8367 /

VT8233A or VT8235 chipsets. It also supports AMD

Athlon

XP / Athlon

Duron

Processors with a FSB (Front Side Bus) frequency of 266 MHz.

The KX400+ Series provides 3 sockets for 184-pin DDR SDRAM with a total

capacity of up to 3GB. You can install DDR333/266/200 (PC2700/2100/1600)
SDRAM, with the option of using the BIOS Setup to over-clock to DDR400.

The KX400+ Series provides one AGP Slot for 1X

、

2X or 4X AGP cards. A CNR

Slot (AMR Type) is used for your audio or modem card (only with KX400+ and
KX400+ PRO).

The KX400+ Series includes built in IDE facilities that support Ultra DMA 33/ 66/

100/ 133 BUS Master Modes. The KX400+ Series also comes with an AC’97 Sound
Codec (ALC650) which supports high quality 6 channel audio (

Super 5.1 Channel

Audio Effect

The KX400+ Series also includes CPU Over Temperature Protection (OTP).

When

you are using a Athlon XP

CPU

,and the CPU

temperature rises above normal

values, the system will automatically

shut down to protect your system from over heating.

The KX400+ and KX400+ PRO also comes preinstalled with

Voice Genie

and

BIOS Mirror

. Voice Genie allows you to select between four languages for audio

diagnostics. BIOS Mirror allows you have a backup (mirror) BIOS when the primary
BIOS is damaged by virus or flash update.

The KX400+ PRO and KX400+ PRO-C also come with two USB 2.0 headers. The

KX400+ comes with one USB 1.1 headers.

Summary of Contents for KX400+ Pro








































































Search results

Summary of Contents for KX400+ Pro

Reviews:

Related manuals for KX400+ Pro

Brands by name

Popular brands

Albatron KX400+ Pro, User Manual

Search results

Summary of Contents for KX400+ Pro

Reviews:

Related manuals for KX400+ Pro

Brands by name

Popular brands