background image

Subject to changes in line with technical progress.

5

3059570

About this manual

About this manual

 

„

The German version is the original operating instructions. All further language versions are translations of the orig-

inal operating instructions.

 

„

Read these operating and assembly instructions carefully before assembly, commissioning and maintenance. This 

is the prerequisite for safe work and trouble-free handling.

 

„

Observe the safety instructions and warnings in these operating and assembly instructions and on the product.

 

„

These operating and assembly instructions are a permanent part of the described product, and must be handed over 

to the buyer if the product is sold.

1.1 

Explanation of symbols

1.1.1 

Safety instructions

 DANGER

This signal word is used to indicate an immediately dangerous situation which, if not avoided, 

will result in death or severe injury.

 WARNING

This signal word is used to indicate a potentially dangerous situation which, if not avoided, 

could result in death or severe injury.

 CAUTION

This signal word is used to indicate a potentially dangerous situation which, if not avoided, 

could result in a minor injury.

 ATTENTION

This signal word is used to indicate a potential risk of property damage.

 NOTE

Special instructions for ease of understanding and handling.

Summary of Contents for EASYAIR flat EF-01

































































Reviews: