AJA BRIDGE LIVE Installation And Operation Manual Download Page 94

Page: 94 / 139

BRIDGE LIVE Video I/O and Streaming Appliance v1.12 94 www.aja.com

Chassis Front

Figure 142. BRIDGE LIVE Chassis Front View

Power Status

Chassis Power Button

The main power switch is used to apply or remove power from the power supply

to the system. Turning off system power with this button removes the main

power but keeps standby power supplied to the system. Therefore, you must

unplug all system power cords before servicing.

Chassis Rear

Figure 143. BRIDGE LIVE Chassis Rear View

SDI Ch 4

SDI Ch 3 SDI Ch 1

Reference

Dual 10Gig Ethernet

Streaming Video I/O

Baseband Video I/O

Redundant Power Supplies

Unused

IPMI

USB Ports (4)

Display Port

SDI Ch 2

Rear Panel Power Supply LEDs

On the rear of each power supply module an LED indicates its status as follows.

• Solid Green: When illuminated, indicates that the power supply is on.
• Solid Amber: When illuminated, indicates the power supply is plugged in and

turned off, or the system is off but in an abnormal state.

• Blinking Amber: When blinking, this system power supply temperature has

reached 63°C. The system will automatically power-down when the power

supply temperature reaches 70°C and restarts when the power supply

temperature goes below 60°C.

Installation Summary

1. Unpack the shipping box, removing the BRIDGE LIVE Quick Start Guide, the

BRIDGE LIVE device, pre-installed rack-ears, rack rails, and two power cords.

2. Mount the physical chassis as desired, using the provided sliding rails.

Cooling airflow enters the chassis from the front, and exits from the rear and

top panels. Do not obstruct these air vents.

Summary of Contents for BRIDGE LIVE












































































































































Search results

Summary of Contents for BRIDGE LIVE

Reviews:

Brands by name

Popular brands

AJA BRIDGE LIVE, Installation And Operation Manual

Search results

Summary of Contents for BRIDGE LIVE

Reviews:

Brands by name

Popular brands