manualshive.com logo in svg

AJA BRIDGE LIVE, Installation And Operation Manual

Share
Download
AJA BRIDGE LIVE Installation And Operation Manual Download Page 46

BRIDGE LIVE Video I/O and Streaming Appliance v1.12 46 www.aja.com

 

In the example above, the HLS stream URL is: 

http://10.8.250.1/hls/segs/master.m3u8

This URL is copied and pasted from the device that is generating the HLS stream 

(in this case, an AJA HELO streaming appliance). 

Auto-Detected Video Streams

To auto-detect the video stream, after you have entered the HLS stream URL, 

select the green Start button in the lower right corner of the BRIDGE LIVE 

interface. After a few seconds, BRIDGE LIVE will auto-detect the HLS video stream 

and display a link under the heading "Auto-detected video streams" shown in 

Figure 54

. 

Click the link. In this example, the link is "Video #1: H.264 1920x1080p @29.97Hz 

4:2:0 8-bit". 
Clicking the auto-detected video stream link simplifies the Input stream 

configuration process because it automatically captures the incoming video 

stream configuration properties. 

Input Stream Video Configuration Options

If you do not select the auto-detected video streams link, under the heading 

"Input stream video configuration options," set the video format to match the 

settings of your HLS stream source. For this example, you would need to set the 

video codec to H.264, the bit depth to 8-bit, and the color sampling as 4:2:0. 

Output Stream Options

Create an output stream in the manner described earlier in this chapter. See 

"Adding the Output Stream" on page 42

. You could output to SDI, MPEG-TS, or 

RTMP(S). 

Summary of Contents for BRIDGE LIVE












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands