manualshive.com logo in svg

Airspan AIRSTAR 1200, Installation Manual, Page: 7 / 36

Share
Download
Airspan AIRSTAR 1200 Installation Manual Download Page 7

AirStar 1900/1200 5G Sub-6 GHz Full gNB/RDU           

2T2R Indoor Radio Unit – Installation Guide 

 

 

© Copyright Airspan Networks Ltd., 2022 

P/N: 

DUG01084

 

Rev. A0.6, Mar 2022 

2

 

 

Warnings and Cautions 

Human Exposure to Radio Frequencies 

The AirStar 1900/1200 5G Sub-6 gHz should be operated from a minimum safe distance of 20 cm (7.87 
in.) during normal operation.  

Radio Interference 

The AirStar 1900/1200 5G Sub-6 generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment on and off, the technician is encouraged to try to correct 
the interference by performing one or more of the following measures: 

 

Re-orientate or relocate the unit  

 

Increase separation between the units and/or End Devices 

 

Connect the equipment to a circuit different from that to which the power source is connected 

Modifications 

Any changes and modifications to this device that are not expressly approved by Airspan Networks 
may void the user's authority to operate the equipment. 

General 

 

Only qualified personnel should be allowed to install, replace, and service the equipment. 

 

The device cannot be sold retail, to the public or by mail order. It must be sold to operators.

 

 

Installation must be controlled. 

 

Installation must be performed by licensed professionals. 

 

Installation requires special training. The AirStar 1900/1200 5G Sub-6 should be installed ONLY by 
experienced installation professionals who are familiar with local building and safety codes and, 
wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to 
do so may void Airspan's product warranty and may expose the end user or the service provider to 
legal and financial liabilities. Airspan and its resellers or distributors are not liable for injury, 
damage or violation of regulations associated with the installation of outdoor units or antennas. 

 

The device is to be installed in a Restricted Access Location not easily accessible.  

 Important Safety Instructions 

 

Read and Save these instructions 

 

This Installation Guide contains instructions and warnings that should be followed during 
installation, and operation.  

 

Failure to follow these instructions could cause bodily injury and/or product failure 

Safety 

1.

 

Read this guide and follow all operating and safety instructions. 

2.

 

Static sensitive components inside - do not remove the lid or base: No user serviceable parts 
inside. 

Summary of Contents for AIRSTAR 1200





































Reviews:

No comments