manualshive.com logo in svg

Airspan AIRSTAR 1200, Installation Manual, Page: 25 / 36

Share
Download
Airspan AIRSTAR 1200 Installation Manual Download Page 25

AirStar 1900/1200 5G Sub-6 GHz Full gNB/RDU           

2T2R Indoor Radio Unit – Installation Guide 

 

 

© Copyright Airspan Networks Ltd., 2022 

P/N: 

DUG01084

 

Rev. A0.6, Mar 2022 

20

 

 

Figure 23: Fix Wall Mount on Wall 

 

6.

 

Slide the Wall mount bracket cover over the Wall mount. 

Figure 24: Slide Wall Mount Cover on Wall Mount 

 

7.

 

Push slightly to engage the protruding pins onto the restraints of the Wall mount cover. 

8.

 

Slide the Hanger onto the mounting pole, until the bottom. 

Figure 25: Slide Hanger on Pole 

 

9.

 

Slide the decorative (bottom) cover over the mounting pole. Verify that the opening is facing 
downward. 

10.

 

Lift the mounting pole (with the Hanger and cover), and insert into the Wall bracket. 

11.

 

Align the holes of the pole and the Wall mount. 

12.

 

Insert the two (2) 1/4 -20 screws, washers and tighten. Tighten to a torque of no more than 
17.5lb*in (1.98 Nm) max. 

Summary of Contents for AIRSTAR 1200





































Reviews:

No comments