Airspan AIRSTAR 1200 Installation Manual Download Page 10

Page: 10 / 36

AirStar 1900/1200 5G Sub-6 GHz Full gNB/RDU

2T2R Indoor Radio Unit – Installation Guide

P/N:

DUG01084

Rev. A0.6, Mar 2022

Purpose

This guide provides the workflow and step-by-step procedures for installing the Airspan’s AirStar
1900/1200 a high performing RU variant. These procedures include:



Verify prerequisites



Install Mounting bracket Wall or Ceiling (Suspended or Solid)



Install the AirStar 1900/1200



Connect and manage cables



Connect power

Intended Audience

This guide is intended for persons who are responsible for installing the AirStar 1900/1200 5G Sub-6.

These persons should have a working knowledge of the equipment.

Document Conventions

This document uses the following typographic conventions.

Table 1: Typographic Conventions

Convention

Element

Blue

underlined

text

Cross-reference links.

Bold text

Keyboard buttons and GUI elements.

Command

Command names or phrases.

Computer output

Text displayed by the computer.

Hyperlinks

Website and e-mail addresses.

Danger

Signifies a hazardous situation—if not avoided—will cause death or
serious injury. Describes how to avoid it.

Warning

Signifies a hazardous situation—if not avoided—can cause death or
serious personal injury. Describes how to avoid it.

Caution

Signifies a hazardous situation—if not avoided—can void the product
warranty, and cause property damage. Describes how to avoid it.



Information/Note

Provides necessary information to explain a task.



Tip

Provides helpful hints.

Summary of Contents for AIRSTAR 1200





































Search results

Summary of Contents for AIRSTAR 1200

Reviews:

Airspan AIRSTAR 1200, Installation Manual, Page: 10 / 36

Search results

Summary of Contents for AIRSTAR 1200

Reviews: