manualshive.com logo in svg

Airspan AIRSTAR 1200, Installation Manual, Page: 17 / 36

Share
Download
Airspan AIRSTAR 1200 Installation Manual Download Page 17

AirStar 1900/1200 5G Sub-6 GHz Full gNB/RDU           

2T2R Indoor Radio Unit – Installation Guide 

 

 

© Copyright Airspan Networks Ltd., 2022 

P/N: 

DUG01084

 

Rev. A0.6, Mar 2022 

12

 

 

4

 

AirStar 1900/1200 5G Sub-6 Installation 

AirStar 1900/1200 5G Sub-6 supports Ceiling (conventional and suspended) and Wall mounting. 

4.1

 

Ceiling Mount 

The following defines the AirStar 1900/1200 ceiling-mount assembly procedure for conventional 
ceiling or suspended ceilings. 

 

Prior to assembly, in any mounting scenario, determine where the unit it to be installed. 

4.1.1

 

Conventional Ceiling Assembly 

The following are instructions for assembly to a conventional ceiling. 

1.

 

Select the required location where the AirStar 1900/1200 unit is to be installed, on the ceiling 
opposite a window. 

2.

 

Position the Ceiling adaptor bracket on the ceiling. Be sure to position the Ceiling adaptor 

so the 

unit will be opposite a window.

 

3.

 

Mark the screw positions carefully through the holes in the Ceiling adaptor bracket onto the 
ceiling. 

4.

 

After drilling holes and inserting approved ceiling anchors (plugs) fasten the Ceiling adaptor 
bracket to the ceiling with screws and washers (not included). 

 

Screws and washers (x4) and any necessary hardware are not supplied by Airspan and are 
the responsibility of the installer. Use appropriate ceiling hardware according to field 
conditions. The holes in the Ceiling adaptor are 5/16 (8mm).  

Figure 3: Fasten the Ceiling Adaptor Bracket to the Ceiling   

 

5.

 

Slide the Hanger onto the pole, till the bottom. 

Summary of Contents for AIRSTAR 1200





































Reviews:

No comments