manualshive.com logo in svg

Airspan AIRSTAR 1200, Installation Manual, Page: 18 / 36

Share
Download
Airspan AIRSTAR 1200 Installation Manual Download Page 18

AirStar 1900/1200 5G Sub-6 GHz Full gNB/RDU           

2T2R Indoor Radio Unit – Installation Guide 

 

 

© Copyright Airspan Networks Ltd., 2022 

P/N: 

DUG01084

 

Rev. A0.6, Mar 2022 

13

 

 

Figure 4: Slide Hanger onto Pole 

 

6.

 

Slide the decorative (lower) cover over the pole. Verify that the opening is facing downward. 

7.

 

Slide the decorative (upper) cover over the pole. Verify that the opening is facing upward. 

8.

 

Lift the mounting pole (with the Hanger and covers) into position and insert into the Ceiling 
adapter. 

 Figure 5: Mounting to the Ceiling Adaptor 

 

9.

 

Align the holes of the pole and the Ceiling adaptor. 

10.

 

Insert the two (2) 1/4 -20 screws, washers and tighten. Tighten to a torque of no more than 
17.5lb*in (1.98 Nm) max. 

Figure 6: Insert Screws 

 

11.

 

At this time, route the cables through the opening in pole and out the bottom, connection will be 
made later. 

12.

 

The Ceiling adaptor bracket is installed and ready for AirStar 1900/1200 unit mounting. 

13.

 

Lift the plastic lower cover, up out of the way in order to hang the unit. 

14.

 

Lift and hook the AirStar 1900/1200 on the hanger. 

Summary of Contents for AIRSTAR 1200





































Reviews:

No comments