39
OPERATING INSTRUCTIONS
THERMOSTAT OPERATION
TIPS FOR USING THE HEATER
•
If the current temperature is -9ºC or lower, the text
“LO” appears in the current temperature view. If the
current temperature is +50ºC or higher, the text “HI”
appears in the current temperature view.
•
A single press of an arrow button changes the
temperature settings by one degree. Pressing an
arrow button for more than two (2) seconds
changes the display setting by one digit per 0.2
seconds.
•
Pressing both arrow buttons when heater is on for
five (5) seconds changes the temperature unit from
Celsius (ºC) to Fahrenheit (ºF). The device uses
Celsius degrees (ºC) by default.
1. Plug in the power cord. Start the heater. When the
heater is in operation, the current temperature is shown
on the left and the set target temperature is shown on
the right.
In this mode, you can set the desired temperature, after which the heater operates automatically and switches itself on
as needed to maintain the set temperature. The thermostat operation is selected by default when the heater is activated.
5. When you press the power button to switch off the
device, the display only shows the current temperature.
3. The temperature can be adjusted with the arrow buttons.
• The temperature can be adjusted within the range
0–40ºC
• The heater’s default setting is 25ºC.
• Pressing an arrow button for two (2) seconds
continuously will change the temperature setting faster.
• The range of the current temperature display
is -9...+50ºC.
2. The corresponding signal light is on when thermostat
operation is selected. To switch from thermostat operation
to timer operation, press the MODE button.
4. When powered on, the heater is activated
automatically when the current temperature drops by
two (2ºC) degrees below the target temperature.
Correspondingly, the heater is deactivated when the
current temperature rises by one degree (1ºC) above the
set target temperature.
9
HOW TO USE
This mode enables the user set the desired temperature, and once it is set, this heater works automatically with running and stop repeatedly
to meet this temperature.
(If power ON and Heater starts operation,the temperature control mode will be operated as default.)
TEMPERATURE CONTROL
The room temp is less than -9 (16 ), the display of
the temp. is 'LO', and more than 50 (99 ) it displays
as 'HI' (50 is not the same value as 99 , actually 37 is
the same value as 99 )
The setting temperature is increased/decreased
1
button for more than 2sec.
the value is increased/decreased by 1 in every 0.2 sec.
simultaneously, the unit is converted from
to , or from to (The default unit is )
1. Push power button.
4. During operaton, the room temp. and setting temp.
both are displayed, and if you push power button
and make the operation stop, only room temp.
is shown.
3. By pushing
desired temperature.
The setting range : 0~40 The default value : 25
temperature is increased/decreased very fast.
The range of current temp display : -9~50
2. By pushing mode button, please select
temperature control mode.
At that time, temperature control lamp is lighten.
than room temp, it starts operation, and
the setting temp is less 1 than
current temp, the operation stops.
Room
temp
＜
Setting temp. … Opeartion (+2 )
Room
temp
＞
Setting temp. … Opearation stop (-1 )
9
HOW TO USE
This mode enables the user set the desired temperature, and once it is set, this heater works automatically with running and stop repeatedly
to meet this temperature.
(If power ON and Heater starts operation,the temperature control mode will be operated as default.)
TEMPERATURE CONTROL
The room temp is less than -9 (16 ), the display of
the temp. is 'LO', and more than 50 (99 ) it displays
as 'HI' (50 is not the same value as 99 , actually 37 is
the same value as 99 )
The setting temperature is increased/decreased
1
button for more than 2sec.
the value is increased/decreased by 1 in every 0.2 sec.
simultaneously, the unit is converted from
to , or from to (The default unit is )
1. Push power button.
4. During operaton, the room temp. and setting temp.
both are displayed, and if you push power button
and make the operation stop, only room temp.
is shown.
3. By pushing
desired temperature.
The setting range : 0~40 The default value : 25
temperature is increased/decreased very fast.
The range of current temp display : -9~50
2. By pushing mode button, please select
temperature control mode.
At that time, temperature control lamp is lighten.
than room temp, it starts operation, and
the setting temp is less 1 than
current temp, the operation stops.
Room
temp
＜
Setting temp. … Opeartion (+2 )
Room
temp
＞
Setting temp. … Opearation stop (-1 )
9
HOW TO USE
This mode enables the user set the desired temperature, and once it is set, this heater works automatically with running and stop repeatedly
to meet this temperature.
(If power ON and Heater starts operation,the temperature control mode will be operated as default.)
TEMPERATURE CONTROL
The room temp is less than -9 (16 ), the display of
the temp. is 'LO', and more than 50 (99 ) it displays
as 'HI' (50 is not the same value as 99 , actually 37 is
the same value as 99 )
The setting temperature is increased/decreased
1
button for more than 2sec.
the value is increased/decreased by 1 in every 0.2 sec.
simultaneously, the unit is converted from
to , or from to (The default unit is )
1. Push power button.
4. During operaton, the room temp. and setting temp.
both are displayed, and if you push power button
and make the operation stop, only room temp.
is shown.
3. By pushing
desired temperature.
The setting range : 0~40 The default value : 25
temperature is increased/decreased very fast.
The range of current temp display : -9~50
2. By pushing mode button, please select
temperature control mode.
At that time, temperature control lamp is lighten.
than room temp, it starts operation, and
the setting temp is less 1 than
current temp, the operation stops.
Room
temp
＜
Setting temp. … Opeartion (+2 )
Room
temp
＞
Setting temp. … Opearation stop (-1 )
9
HOW TO USE
This mode enables the user set the desired temperature, and once it is set, this heater works automatically with running and stop repeatedly
to meet this temperature.
(If power ON and Heater starts operation,the temperature control mode will be operated as default.)
TEMPERATURE CONTROL
The room temp is less than -9 (16 ), the display of
the temp. is 'LO', and more than 50 (99 ) it displays
as 'HI' (50 is not the same value as 99 , actually 37 is
the same value as 99 )
The setting temperature is increased/decreased
1
button for more than 2sec.
the value is increased/decreased by 1 in every 0.2 sec.
simultaneously, the unit is converted from
to , or from to (The default unit is )
1. Push power button.
4. During operaton, the room temp. and setting temp.
both are displayed, and if you push power button
and make the operation stop, only room temp.
is shown.
3. By pushing
desired temperature.
The setting range : 0~40 The default value : 25
temperature is increased/decreased very fast.
The range of current temp display : -9~50
2. By pushing mode button, please select
temperature control mode.
At that time, temperature control lamp is lighten.
than room temp, it starts operation, and
the setting temp is less 1 than
current temp, the operation stops.
Room
temp
＜
Setting temp. … Opeartion (+2 )
Room
temp
＞
Setting temp. … Opearation stop (-1 )
9
HOW TO USE
This mode enables the user set the desired temperature, and once it is set, this heater works automatically with running and stop repeatedly
to meet this temperature.
(If power ON and Heater starts operation,the temperature control mode will be operated as default.)
TEMPERATURE CONTROL
The room temp is less than -9 (16 ), the display of
the temp. is 'LO', and more than 50 (99 ) it displays
as 'HI' (50 is not the same value as 99 , actually 37 is
the same value as 99 )
The setting temperature is increased/decreased
1
button for more than 2sec.
the value is increased/decreased by 1 in every 0.2 sec.
simultaneously, the unit is converted from
to , or from to (The default unit is )
1. Push power button.
4. During operaton, the room temp. and setting temp.
both are displayed, and if you push power button
and make the operation stop, only room temp.
is shown.
3. By pushing
desired temperature.
The setting range : 0~40 The default value : 25
temperature is increased/decreased very fast.
The range of current temp display : -9~50
2. By pushing mode button, please select
temperature control mode.
At that time, temperature control lamp is lighten.
than room temp, it starts operation, and
the setting temp is less 1 than
current temp, the operation stops.
Room
temp
＜
Setting temp. … Opeartion (+2 )
Room
temp
＞
Setting temp. … Opearation stop (-1 )
SUOMI
ENGLISH
SVENSKA NORSK D
ANSK
