38
OPERATING INSTRUCTIONS
ACTIVATION AND DEACTIVATION
TIPS FOR USING THE HEATER
• The heater is activated when the adjusted temperature is 2°C higher than the ambient temperature.
• After activation, the heater defaults to thermostat operation.
• When the device is deactivated, all timer functions are reset and must be set again if they are needed.
1. START THE HEATER
• Press the power button. The device emits an audio
signal upon activation.
• The device can be switched off by pressing the same
button.
2. SELECT THE OPERATING MODE
• Select the desired operating mode, either
thermostat or timer operation.
• You can make the selection with the MODE button.
• The default is thermostat operation.
3. SET THE TARGET TEMPERATURE OR HEATING TIME WITH THE ARROW BUTTONS
• The temperature can be adjusted between 0–40 ºC.
• The minimum heating time in timer operation is 10 min, and maximum of 55 min or continuous use.
NOTE!
After activation, the heater’s default operating mode is thermostat operation, which is shown by the corresponding
indicator light.
SHUTDOWN TIMER
If you would like the heater to switch off on its own, you can use the shutdown timer.
Use the TIMER button to activate the shutdown function. Then select the desired shutdown
delay with the arrow buttons. The minimum delay is 30 minutes.
8
HOW TO USE
OPERATION & STOP
In order to operate, set the temperature higher than room temperature.
After power On, the default mode is temperature control mode.
During the operation if you push power button, the heater stops and the off timer function is
cancelled.
The model equipped solenoid valve (by-pass device) makes the remaining oil returned to the oil tank.
For 2sec. from the time of burner off, the solenoid valve operates, which makes remaining oil
returned to the oil tank, and by this device, the smell caused by unburned gas
is remarkably shrunk.
There are a preheater and a preheater temperature sensor to improve the ignition when operating the heater.
As a result, the operation time of the heater may vary depending on the ambient temperature at the power input.
(The display then turns on the flame indicator.)
1.
Heater will turn ON with "beep" sound, and
automatically operate.
If you wish to stop the unit, press "Power" button
one more time.
2. SELECT THE DESIRED OPERATION TYPE USING
"MODE" BUTTON.
You can set the desired temperature between "0~40 ".
Set the desired time limit between 10min ~ Continuous operation
8
HOW TO USE
OPERATION & STOP
In order to operate, set the temperature higher than room temperature.
After power On, the default mode is temperature control mode.
During the operation if you push power button, the heater stops and the off timer function is
cancelled.
The model equipped solenoid valve (by-pass device) makes the remaining oil returned to the oil tank.
For 2sec. from the time of burner off, the solenoid valve operates, which makes remaining oil
returned to the oil tank, and by this device, the smell caused by unburned gas
is remarkably shrunk.
There are a preheater and a preheater temperature sensor to improve the ignition when operating the heater.
As a result, the operation time of the heater may vary depending on the ambient temperature at the power input.
(The display then turns on the flame indicator.)
1.
Heater will turn ON with "beep" sound, and
automatically operate.
If you wish to stop the unit, press "Power" button
one more time.
2. SELECT THE DESIRED OPERATION TYPE USING
"MODE" BUTTON.
You can set the desired temperature between "0~40 ".
Set the desired time limit between 10min ~ Continuous operation
8
HOW TO USE
OPERATION & STOP
In order to operate, set the temperature higher than room temperature.
After power On, the default mode is temperature control mode.
During the operation if you push power button, the heater stops and the off timer function is
cancelled.
The model equipped solenoid valve (by-pass device) makes the remaining oil returned to the oil tank.
For 2sec. from the time of burner off, the solenoid valve operates, which makes remaining oil
returned to the oil tank, and by this device, the smell caused by unburned gas
is remarkably shrunk.
There are a preheater and a preheater temperature sensor to improve the ignition when operating the heater.
As a result, the operation time of the heater may vary depending on the ambient temperature at the power input.
(The display then turns on the flame indicator.)
1.
Heater will turn ON with "beep" sound, and
automatically operate.
If you wish to stop the unit, press "Power" button
one more time.
2. SELECT THE DESIRED OPERATION TYPE USING
"MODE" BUTTON.
You can set the desired temperature between "0~40 ".
Set the desired time limit between 10min ~ Continuous operation
TIMER OPERATION
THERMOSTAT OPERATION
8
HOW TO USE
OPERATION & STOP
In order to operate, set the temperature higher than room temperature.
After power On, the default mode is temperature control mode.
During the operation if you push power button, the heater stops and the off timer function is
cancelled.
The model equipped solenoid valve (by-pass device) makes the remaining oil returned to the oil tank.
For 2sec. from the time of burner off, the solenoid valve operates, which makes remaining oil
returned to the oil tank, and by this device, the smell caused by unburned gas
is remarkably shrunk.
There are a preheater and a preheater temperature sensor to improve the ignition when operating the heater.
As a result, the operation time of the heater may vary depending on the ambient temperature at the power input.
(The display then turns on the flame indicator.)
1.
Heater will turn ON with "beep" sound, and
automatically operate.
If you wish to stop the unit, press "Power" button
one more time.
2. SELECT THE DESIRED OPERATION TYPE USING
"MODE" BUTTON.
You can set the desired temperature between "0~40 ".
Set the desired time limit between 10min ~ Continuous operation
