manualshive.com logo in svg

AirMagnet PRG-Laptop 7.0, Reference Manual, Page: 178 / 210

Share
Download
AirMagnet PRG-Laptop 7.0 Reference Manual Download Page 178

170

Chapter 9: Problematic Traffic Pattern

AirMagnet Laptop Wireless LAN Policy Reference Guide

Excessive Fragmentation Degrading Performance 

The 802.11 MAC layer supports the processes of fragmentation and 

defragmentation. The process of partitioning an 802.11 frame into 

smaller frames for transmission is called fragmentation; it helps to 

increase reliability and reduce errors.  In cases where channel 

characteristics limit reception availability, transmitting in smaller 

(fragmented) frames  increases the probability of successful 

transmission. Fragmentation is accomplished at each immediate 

transmitter before the actual start of transmission. The process of 

recombining fragmented frames into the original unfragmented 

longer frame is defined as defragmentation. The IEEE 802.11 

standard defines the packet format to identify fragmented frames for 

defragmentation (illustrated below).

Figure 9-2: IEEE 802.11 Frame fields for frame fragmentation and 
defragmentation

The increased reliability of the smaller fragmented frames comes at 

the cost of frame transmission overhead. The frame is divided into 

different segments depending upon the fragmentation threshold. The 

placement of the fragments in the fragmentation process is decided 

by the "sequence control field" as shown in the figure above. The 

"more" field indicates if the fragment is the last fragment.  If too many 

frames are requiring fragmentation and defragmentation, network 

overhead will be reduced and there may be a larger problem causing 

the fragmentation.
AirMagnet Mobile tracks the fragmentation statistics on the network 

and alerts on abused fragmentation usage that could lead to 

degraded WLAN performance. The fragmentation threshold needs to 

be carefully set to balance the benefit and overhead.  Typically, 

equipment vendors set the default fragmentation threshold to 1536.  

Consult your equipment documentation and ensure that the 

manufacturer's recommendations are met.

Laptop Wireless LAN Policy Reference Guide.book  Page 170  Thursday, January 25, 2007  5:36 PM

Summary of Contents for PRG-Laptop 7.0



















































































































































































































Reviews:

No comments