manualshive.com logo in svg

AirMagnet PRG-Laptop 7.0, Reference Manual, Page: 162 / 210

Share
Download
AirMagnet PRG-Laptop 7.0 Reference Manual Download Page 162

154

Chapter 8: IEEE 802.11e and VoWLAN Issues

AirMagnet Laptop Wireless LAN Policy Reference Guide

a) the amount of time a station senses the channel to be 

idle before backoff or transmission.
b) the length of the contention window for the backoff.
c) the duration a station may transmit after it acquires the 

channel.

• HCF Controlled Channel Access (HCCA): This mechanism 

allows reservation of transmission opportunities (TXOPs: 
Time intervals in which the QSTA can transmit frames) with 
the Hybrid Co-ordinator (HC: co-located with the QAP). A 
QSTA requests the HC for TXOPs - both for its own transmis-
sions as well as transmissions from the QAP to itself. The 
request is initiated by the Station Management Entity (SME) 
of the QSTA. Based on the admission control policy, if the 
request is accepted, the HC schedules TXOPs for both the 
QAP and the QSTA. For transmissions from the QSTA, the 
HC polls the QSTA based on the parameters supplied by the 
QSTA at the time of its request. For transmissions to the 
QSTA, the QAP directly obtains TXOPs from the collocated 
HC and delivers the queued frames to the QSTA, again 
based on the parameters supplied by the QSTA.

Figure 8-1: MAC frame format

VoWLAN, an extension of VoIP, is considered to be the next killer 

application for WLANs. The various components are:

• a wi-fi enabled phone
• an access point to which the phone will associate
• at upper layers, a PBX system that may connect to a public 

telephone network (or the communication could be through 

the Internet).

The two most important issues that need to considered in a VoWLAN 

deployment are:

• capacity: number of phones or concurrent calls per cell

Laptop Wireless LAN Policy Reference Guide.book  Page 154  Thursday, January 25, 2007  5:36 PM

Summary of Contents for PRG-Laptop 7.0



















































































































































































































Reviews:

No comments