506878-01
Page 24 of 62
Issue 1139
General Guidelines for Vent Terminations
n Non–Direct Vent applications, combustion air is taken from
indoors and the flue gases are discharged to the outdoors.
This furnace is then classified as a non–direct vent, Category
IV gas furnace.
In Direct Vent applications, combustion air is taken from
outdoors and the flue gases are discharged to the outdoors.
The furnace is then classified as a direct vent, Category IV
gas furnace.
In both Non–Direct Vent and Direct Vent applications, the
vent termination is limited by local building codes. In the
absence of local codes, refer to the current National Fuel
Gas Code ANSI Z223-1/NFPA 54 in U.S.A., and current
CSA-B149 Natural Gas and Propane Installation Codes in
Canada for details.
In Direct Vent applications, the vent termination is limited
by local building codes. In the absence of local codes, refer
to the current National Fuel Gas Code ANSI Z223-1/NFPA
54 in U.S.A., and current CSA-B149 Natural Gas and
Propane Installation Codes in Canada for details.
Position termination according to location given in Figure
19. In addition, position termination so it is free from any
obstructions and 12" above the average snow accumulation.
For Canadian Installations Only:
In accordance to CSA International B149 installation
codes, the minimum allowed distance between the
combustion air intake inlet and the exhaust outlet of other
appliances shall not be less than 12 inches (305 mm).
IMPORTANT
Do not use screens or perforated metal in exhaust
terminations. Doing so will cause freeze-ups and may
block the terminations.
IMPORTANT
At vent termination, care must be taken to maintain
protective coatings over building materials (prolonged
exposure to exhaust condensate can destroy protective
coatings). It is recommended that the exhaust outlet
not be located within 6 feet (1.8 m) of a condensing
unit because the condensate can damage the painted
coating.
NOTE:
If winter design temperature is below 32° F (0° C),
it is recommended that the exhaust piping be insulated with
1/2" (13 mm), Armaflex or equivalent when run through an
unconditional area. In extremely cold climate areas with
temperature below 20° F (6.7° C) it is recommended that,
3/4" (19 mm) Armaflex or equivalent be used. Insulation on
outside runs of exhaust pipe may be painted or wrapped to
protect insulation from deterioration in accordance with the
insulation manufacturers recommendation. Exhaust pipe
insulation may not be necessary in some specific
applications.
NOTE:
During extremely cold temperatures, below
approximately 20° F (6.7° C), units with long runs of vent
pipe through unconditioned space, even when insulated,
may form ice in the exhaust termination that prevents the
unit from operating properly. Longer run times of at least 5
minutes will alleviate most icing problems. Also, a heating
cable may be installed on exhaust piping and termination
to prevent freeze-ups. Heating cable installation kits are
available see unit specification sheets for part numbers.
Follow the next two steps when installing the unit in
Non–
Direct Vent applications
where combustion air is taken
from indoors and flue gases are discharged outdoors
.
1. Use field-provided materials and the factory-provided
air intake screen to route the intake piping as shown in
figure 25 or 26. Maintain a minimum clearance of 3"
(76 mm) around the air intake opening. The air intake
opening (with the protective screen) should always be
directed forward or to either side in the upflow position,
and either straight out or downward in the horizontal
position.
The air intake piping must not terminate too close
to the flooring or a platform. Ensure that the intake
air inlet will not be obstructed by loose insulation
or other items that may clog the debris screen.
2. Use a sheet metal screw to secure the intake pipe to
the connector, if desired
Summary of Contents for 95G2UHV
